microcentrifuge tube opener 3d models
238495 3d models found related to microcentrifuge tube opener.thingiverse
Larger than normal size microtube rack for all of your biology needs! ...Fits most standard sized microcentrifuge tubes with plenty of room in between tubes.
youmagine
Link to publication:http://pubs.acs.org/doi/abs/10.1021/acsomega.7b01310 This particular part is meant to allow reproducible analysis of samples held in a micro-centrifuge tube (VWR Microcentrifuge, Cat No. 20170-333). This adapter can be used in...
thingiverse
Link to publication: http://pubs.acs.org/doi/abs/10.1021/acsomega.7b01310 This particular part is meant to allow reproducible analysis of samples held in a micro-centrifuge tube (VWR Microcentrifuge, Cat No. 20170-333). This adapter can be used in...
thingiverse
This is a small rack for 1.5 ml microcentrifuge tubes (11 mm diameter). 20 tubes can be stored in the rack. ... The rack consists of four different parts which have to be put together and can be secured with two M3 nuts and two M3x16 screws if...
thingiverse
This is a simple rack to hold four 1.5 or 2.0 ml microcentrifuge tubes. Tubes from different manufacturers should be more or less the same size, and the few brands I've tried have fit fine. ... ...
thingiverse
This is a StageTip Adaptor for microcentrifuge tube for stagetip made with peptide tips. It provides more secure holding of the StageTip in the eppi tube so it can be span at a higher speed to shorten washing and elution step. ... Gcode included to be...
thingiverse
I designed this box to put my Eppendorf tubes in during incubation, this allows me to lie the tube on its side in the shaker without the worry of the tube popping open. Can print without supports if oriented in the correct way. ... I currently...
thingiverse
... on the balance easier. Edit 9/26/2018: Updated V3 for 5 mL tubes, removed V1 Updated V2 with a slight incline on the bottom of the holder. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/7rSmxc9lKFF
thingiverse
I needed to vortex 20+ Eppi tubes at once for some biology experiments. This thing lets me do that! ... Only other part required is a small length of ~8mm rod (could probably get away with printing it).
thingiverse
Simple Microcentrifuge tube rack that holds 100 1.5ml tubes. To save on filament I made no feet and let the tubes hold up the racks. ... Dimensions are 148.5 x 148.5 x 1 mm
thingiverse
The outer diameter of 1.5mL Eppendorf microcentrifuge tubes is approximately 10.9mm by my measurements. However, when printing with a 0.8mm nozzle, I had to design the holes as large as 12.2mm for the eppendorf tubes to fit easily. I have not...
thingiverse
This lid holds 9 1.5mL microcentrifuge tubes but I will be making more lids that cater to a wider range of tubes including the 50mL, 15mL, and even 0.2mL PCR tubes. Now for the dorky part: Data! After freezing about 250mL of tap water in the system...
thingiverse
It has been designed to store solution at 4°C in microfuge tubes if you manage to print or build it in aluminium for example. The carrier respects the standard dimensions and should fit all pipetting robots (Beckman, Tecan, Hamilton). This carrier...
thingiverse
####0.2 mL PCR Tube Rotor This is an alternate rotor designed for a benchtop mini-microcentrifuge. It can hold standard 0.2 mL PCR tubes and works well with individual tubes or 8-tube strips. For a mini-microcdentrifuge like the the one pictured,...
thingiverse
Here is a simple holder for a 1.5 ml or 2 ml microcentrifuge (‘Eppendorf’) tube, as part of my 3d printing labware range. ...The goal was to make items which: - Are functional (in this case securely holding tubes upright) - Use minimal plastic, and so...
prusaprinters
0.2 mL PCR Tube Rotor This is an alternate rotor designed for a benchtop mini-microcentrifuge. ...It can hold standard 0.2 mL PCR tubes and works well with individual tubes or 8-tube strips. For a mini-microcdentrifuge like the the one pictured, the...
thingiverse
The hole spacing has been tested and the diameter fits tubes with or without a skirt, and with labels attached, though they may need cleaning out with a drill depending on your print quality. Probably best printed in PLA to avoid any warping. ...Edit:...
thingiverse
A Secret Santa gift for a colleague who likes Totoro. I printed all parts separately and had to sand a bit so that they fit, so please consider making inserted parts slightly smaller. ...It is printed with PETG, supports are not required.
myminifactory
A small wrench for opening oil paint tubes, ointments, and toothpaste caps.
thingiverse
remixed pcr tube opener, a mix of https://www.thingiverse.com/thing:2272015 and https://www.thingiverse.com/thing:2303697
thingiverse
A small wrench for opening oil paint tubes, ointments and toothpaste caps. ...Useful for people with arthritis and plein aire painters.
thingiverse
It was designed for a talented young artist whose major barrier to creativity is that she can't open her tubes of paint. It has also found use by people with arthritis for opening small containers. Designed for paint tube caps from about 10–25 mm in...
thingiverse
Easy to print test tube opener designed to make sample handling easier. Protection shields are used for decreasing the probability of contamination. The design has been tested on [FL Medical Sterile test...
cults3d
Easy to print test tube opener designed to make sample handling easier. Protection shields are used for decreasing the probability of contamination. The design has been tested on FL Medical Sterile test tube used in a local hospital, where laborants...
myminifactory
Open your frozen treat one handed with this opener. I thought I would create a otter pop opener because i was board. 20 minutes of cad and 2 hours of printing later. Intigrated end scrap ejection port for continuous use. Works for most openeing...