minelab equinox metal detector 3d models

wall mount for equinox metal detector from minelab 3 screws fixing with logo your detector will no longer drag in your room or in your garage.

folding tripod for equinox minelab metal detector for 600/800/900 series. more practical for transporting your detector as it can be folded onto the rod. ... easy assembly and very light

Protective Control Cover for the Minelab Equinox 800 metal detector

I was unable to find a quick release or re-locator for the Minelab Equinox metal detector I'd just bought and the only option was paying over 40 dollars to buy one, so I sat down got my calipers out and started taking measurements. after weeks of...

Bracket to carry your Garrett "carrot" pinpointer on your Minelabs Equinox (600 or 800). ... Print with at least 40% infill

Simple lightweight stand for the Minelab Equinox shaft to stop your detector tipping over on the ground. ...This fits Equinox or Vanquish with the Equinox shaft Mod.

metal detector minelab part it dose the job print at 70% to 100% infill .

Just a clamp for my MineLab Equinox 600 wires

s-rod adaptor for equinox 600/800 with storage box for found coins

Minelab GO60 Metal Detector gofind wall mount mount holes approximately 8.25 cm apart

Simple Metal Detector stand that fits the Minelab Equinox series. (600 or 800) There are two versions of the stand. One with logo, one blank. I have this stand mounted so that it rests against the bottom of the control box arm. (See...

Simple Metal Detector stand that fits the Minelab Equinox series. (600 or 800) There are two versions of the stand. One with logo, one blank. I have this stand mounted so that it rests against the bottom of the control box arm. ...(See pictures)...

Simple Metal Detector stand that fits the Minelab Equinox series. (600 or 800)</p> <p>There are two versions of the stand. One with logo, one blank.</p> <p>I have this stand mounted so that it rests against the bottom of the control box arm. ...(See...

Little on the chunky side, but feels ok. Designed to use 5mm bolts tapped, but could use Brass inserts. Button is generic 14mm round push button, little tight to get in but hold ok. I have done at 0.2 layer height and at 50% rect. ...seems ok.

I wanted to hang my Minelab Equinox 800 on the wall so I don't trip on it, but couldn't find a solution I was happy with. Here I designed a slightly ramped double arm wall mount to grab the arm cuff at the bottom. Surprisingly, PLA at 20% intfil...

This is essentially a remix of "Alien1994"'s equinox bumper to give it an extra rugged look...the fit however is far from perfect and is not really meant for purpose at this stage. I printed this with TPU and it sort of fits, but needs some work. ...I...

This is a Remix of Glompie Minelab Excalibur lower shaft. I remixed this for use on my Nox 600 carbon shaft setup that i bulit my self.. lower shaft OD20mm ID18mm. The Text on the shaft can be paiinted like in the picture. ... So this...

Note that stock foot pads on the detector must be in good condition in order to use the mount. Not designed for mobile use. Fine for home or shop. Use two plastic anchors to mount to wall. ... If you don't have a 3D printer look for it on...

The same applies for option 2 the Minelab 35 Pro pinpointer and Deus MI-6 and MI-4. Print the universal clip and then select the option you want and clip the two part together after printing. ... The Hori Hori garden dig knife used for this is...

bipod support to protect your detector. ...light and robust it will accompany you in all your detection. it fits on the rod of minelab equinox 600 or 800

Stand for Equinox 600 or 800 metal detector. Needs supports. Remix of https://www.thingiverse.com/thing:3143547 And remix of https://www.thingiverse.com/thing:2501105 I made legs from scratch. Beefed up the leg part where it mated to cuff...

With some users having trouble with there stock equinox arm cuff I thought I may as well design a stronger version. ...Hope it helps.

Reinforcement for Equinox 15" coil anchor tabs. One STL ,if printing in one piece is preferred. Two others have the pieces separately to be bonded with Ciano acrylate after printing. The printing position shown in the photos is recommended ,in...

A minelab Equinox 800 or 600 15" coil mounting tab protector

Arm cuff for Minelab Equinox 600 or 800. Both pieces are compatible with the OEM cuff. Two versions: Note: The OEM cuff has a metal insert for the M4 thumb screw. 1. The Arm Cuff.STL is used with a M4 X 35mm screw and nut. Nut fits inside slot.

This is a hard bump case for the Equinox 800 and 600 metal detectors - the best selling metal detectors worldwide for the last few years. It is designed to be printed with rigid filament, preferably PETG. It is slimmer and more lightweight (~16g)...

I created simple but reliable cable clip clamp for cable of coil to metal detectors. Dimensions are 6 mm cable and 20 mm shaft. Usable for upper (aluminium) shafts of all metal detectors with that dimensions. Fits very well to: - Fisher -...

Arm cuff for Minelab Equinox 600 or 800. the original was too large so i made this one smaller. it is about 94mm across vs 120mm of the original. this is just the top section but it works with the original bottom, or print the bottom from ...

Enjoy the Minelab EQUINOX bumper cover, this is a tight fit slip on cover. If you found this useful, please donate what you think it is worth to my http://paypal.me/DOHara1994 Help cover the time of design. Thanks, Enjoy! ...

Hello !I created simple but reliable cable clip clamp for cable of coil to metal detectors.Dimensions are 6 mm cable and 20 mm shaft. Usable for upper (aluminium) shafts of all metal detectors with that dimensions. ...I use that cable clip clamp and...