mobilink tnc 3d models

TNC J01010A0045

TNC J01010A0048

Wire connector TNC Female

TNC Switch for electric panel

This is TNC 4 hole, Female Panel Mount.

TNC metal cap

TNC-SMA J01019A0028

WVCARC Case for TNC standalone version i did not design this only sharing it here so other people can make it Link to resource https://www.wvcarc.com/p/tnc-96k-resources.html

... a TNC for my Baofeng. ... Check out http://na7q.com/baofeng-tnc/ I felt like it should have a case to better protect it. Just slip the TNC into the sleeve then super glue the lid over the USB end. ...Only a light amount of glue should be used.

... TNC-Pi 9k from WVARC. ...I put it on the Raspberry Pi and wanted a case for the Pi 4 and the TNC-Pi 9k. https://www.wvcarc.com/2018/03/tnc-pi-9k-kits.html I use 4x 2.5mmx35mm Screws to keep it together. ...https://www.amazon.com/gp/product/B0789W9RNJ

The CM108 is a very common, cheap USB audio chip with a few GPIO which make it ideal for creating a TNC: https://www.aliexpress.com/wholesale?trafficChannel=main&d=y&CatId=0&SearchText=cm108<ype=wholesale&SortType=price_asc&groupsort=1&page=1 This is...

This mount goes inside of the taranis and holds a TNC PCB connecter like this:...

The Tremor Nail Clipper (TNC) is an innovative assistive technology (AT) to enable humans struggling with hand tremors to clip their nails independently, thus helping with the day to day life. It clamps onto most tables (thickness under 5cm), and...

TNC-1. ... Photogrammetry by Kent Mead.

If you use 0110-M-P case (https://www.thingiverse.com/thing:922740) or a variant of it AND you wish to stack a TNC-Pi 2 on top of it, here is the solution! Print it and add it to your actual case as an extension. It will protect your TNC-Pi 2. ...

... the TNC should fit snug enough that it doesn't fall out. If you want to protect the button from getting pressed in error, you can insert the TNC so that the button is against the wall of the case. Hope others can get some use out of this. ...

This is an of the shelf item - Souriau - for coax cable.

Custom case to enclose the wonderful mobilinkd TNC http://www.mobilinkd.com

Mast mount for a TNC socket, usually used for WiFi installations. Requires 2x M5 nuts and bolts. ... Rotate 180 degrees before printing.

Mast mount for a TNC socket, usually used for WiFi installations. Requires 2x M5 nuts and bolts. ... Rotate 180 degrees before printing.

This is a model of a Rosenberger TNC RF Sealed Bulkhead Connector that is used with RG-405 semi-rigid coax 0.085" diameter (p/n : 56K511-271N5)

Another remix. ...This time it will hold a TNC-Pi 2. If you do not want to stack them above the Pi, here you go! ... Enjoy!

This is a model of a Rosenberger TNC Coaxial Bulkhead Connector that is good up to 10 GHz.It is mounted from the outside and with the locknut and nut inside the housing.Other comparable (but not exact) parts well worth considering are the Amphenol RF...

Subsriber : https://goo.gl/72RGFJ

Customized version of https://www.thingiverse.com/thing:356988 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=356988

conector usado em antena de celular

This is a model of an Rosenberger TNC Right Angle PCB Coaxial Connector rated to 10 GHz (p/n : 56K201-400A5 )

This is a model of an Amphenol RF TNC Coaxial Bulkhead Vertical PCB Connector rated to 11 GHz (p/n : 122440).

I don't like when adapters are rolling around on my table, so that's why I made this little adapter holder for PL, BNC and TNC adapters. ... I stick some ant-slip rubber feet on the bottom.

I don't like when adapters are rolling around on my table, so that's why I made this little adapter holder for PL, BNC and TNC adapters. ... I stick some ant-slip rubber feet on the bottom.