nano talon 3d models
11444 3d models found related to nano talon.thingiverse
This is a replacement clip for the ZOHD Nano Talon wing. ...It was created with Sketchup
thingiverse
This is a USB socket to be use with flight controllers (like iNav ones) for the Nano Talon.
thingiverse
Holder for VTX for ZOHD Nano Talon to be used on a nose canopy.Fits AKK X2-Ultimate but should fit also other VTXes
thingiverse
Just a really simple wall mount for the Nano Talon - I wanted to hang it on the wall, just print two of these and then it will hang by the wings.
thingiverse
This is a work in progress. ...After several accidents I decided to design a nose cover for my Nano Talon. ...The idea is not only replace the original, I would like to incorporate some mods to it.
thingiverse
For Nano Goblin mod. ...Place servos on wing. v3 is thin, v4 is more robust. Some more details (plenty of photos) on our French forum: http://www.france-fpv.fr/viewtopic.php?f=15&t=1117&hilit=nano+talon&start=220
thingiverse
made a new baseplate for the nano talon after i crashed mine. ... I have set the strap holes 40mm apart at the same plase but have taked away all the other holes have also made a pressfit mount for the runcam split ...
thingiverse
I designed this in Tinkercad out of necessity after seeing 5 Nano Talons, at my local club, have the same part broken from normal use. This is designed to clip over the wing support and reinforce it. ... It does clip on and that should work but for...
thingiverse
All three parts for the Tail Wing mechanism of the Nano talon with tight tolerances in order to have more accurate tail wing movement. The horn holes have been designed 0.5mm in order to be drilled out and have a tight fit on push rod. Depending...
thingiverse
A mount, bracket, clip, call it what you want; but this is a must have if you have a nano talon! This mount is used for placing your camera on and holding it in place. ...A 'stylish' looking yet, useful thing * It has a 10% up angle so the canopy...
thingiverse
This is a direct fit for the nano talon. It is 0.4 mm thicker than the original and makes for a slightly tighter fit of the wings to the fuselage. I printed this on its side with a tiny support under the vertical brace so the print layers would run...
thingiverse
Having the nth spin of death, I lost a piece of my beloved nano talons' nose. To re-establish (sort of) the integrity of the front' I designed a prothesis. Prints straight forward, no support needed if you use CURAs' experimental "Make printable...
thingiverse
I didn't like the velcro tape that was intended to attach the battery to the base plate of my NANO TALON. It was too thin and the battery was still shaking. so i designed two versions of clips which fit my batteries. version 1.x is for a 3S...
thingiverse
Link to RCGroups thread here: https://www.rcgroups.com/forums/showthread.php?2916952-ZOHD-Nano-Talon-860mm-Wingspan-%2A%2A%2AOfficial-Thread%2A%2A%2A Thanks to alicecooper for the idea! V2 Knob has been uploaded. Old knob was for a 3mm plate. ...The...
thingiverse
Antenna holder for ZOHD nano talon. ...Use with a pigtail equiped VTX
thingiverse
I needed a way to mount the FPV video TX antenna to the Nano Talon.
thingiverse
Simple replacement canopy lock for the ZOHD Nano Talon designed in SketchUp.
thingiverse
1 axis gimbal for Runcam Split 2 inside Nano Talon fuselage. ... Servo for gimbal: Corona 919MG Digital Metal Gear Servo
thingiverse
This is an extention for the rod of the Nano Talon. The rod extention is 82mm long and the link is 20mm long. ...
thingiverse
Mount for a Eachine TX805 and a Mobius Action cam for the ZOHD Nano Talon. ... Printed with PETG, 10% infill and support.
thingiverse
This is a custom USB Side Port for my Nano Talon so that I can have the Custom iNav Flight Controller in the 0 degree Orientation so I can plug the USB lead in without access issue. ... Hope this is of some use to you fellow Nano Talon Owners :-) Cheers...
thingiverse
I have combined the air scoop inlet for nano talon from: (https://www.thingiverse.com/thing:2878770) by @https://www.thingiverse.com/osprey_64 with the original mount that came with the model. You can also use the same screws that the model came...
thingiverse
Replacement for ZOHD Nano Talon base plate. This is not direct 1-to-1 project. Holes and cuts are in slightly different places to create a more secure base for 4S battery. ...External dimensions are the same