nerf holster 3d models
9893 3d models found related to nerf holster.thingiverse
... the holster. One around a worn belt and the other around the leg. I have not had the chance to print this myself yet. Refer to the original for other notes. I will update this once I have printed it. Holster.obj shows the pieces assembled.
thingiverse
Pros and cons of this holster vs other Nerf holsters available: Cons -Requires you to drill holes in the shell of your blaster to mount the attachment rail/spindles. -The spindles may wear out over time and need replacement. -The spindles sticking...
thingiverse
A nerf holster, can hold any blaster if it does not interfere. Meant as a small of back backup. I printed this on a dremel3d idea builder, at medium settings, and that's what i've used to prototype. ...FYI you might need to do a little cleanup.
thingiverse
This a Nerf Jolt holster, that is meant to be used with Jolts without the front barrel cap piece. This is also my first "major" design in Solidworks! It took about 4 hours or so to design, and keep in mind I haven't done any test prints yet, I will...
thingiverse
Have fun with the most badass nerf holster ever! nerfholsterclip.stl (a derivative of radio belt clip by Shaputer: http://www.thingiverse.com/thing:12796) - Good results with 30% infill, 3 shells, .3 mm layer, 225c (filament dependent - I like the...
thingiverse
This is for holstering your NERF jolt. press the release catch to release the NERF jolt. As seen, the release catch relies on a rubberband to work. There's a slot in the front to clip a flashlight too. Take note that this will only accept the...
thingiverse
This is meant to be a quick way to holster your Nerf Snapfire. You will need 8 cable ties, 6 for the snapfire itself, and 4 for the holster itself. Or you can always superglue or screw this to your snapfire if you'd like. Instructions Just use the...
thingiverse
My brother plays paintball and they use the small roughly 2x3 inch nerf footballs in scenario games and he asked me to make a holster after the one pictured. ...I only printed one pieces for a prototype before sending him the files to print so not sure...
thingiverse
A holder for some magnets so you can carry your nerf gear and blaster without clunky holsters or or a sling HARDWARE magnets...
thingiverse
A Nerf Jolt EX-1 holster, may not be compatible with newer variants of the blaster without removing the orange tip. Holds onto blaster with a mag-release styled lever. I designed this years ago for my own personal battle belt, and it wasn't meant...
thingiverse
A holster for the Nerf Triad. Printed at 0,3mm. No Supports needed. No dropping out so far :) **Update 04.09.2018:** -File HolsterTriadWithKnobs.stl added. Some small knobs were created to better retain the balster **Update 05.09.2018:** ...
thingiverse
This is a simple holster for the Nerf BigShock Mega Pistol. The spine comes in two styles - one for MOLLE webbing and the other for 2" belts. It uses (4) 2-56 socket head screws that are 1/4" long and (4) 3/16" nuts to hold the two parts together. M2...
thingiverse
This is a spin off from my Snapfire holster, by popular demand.http://www.thingiverse.com/thing:257060 except, i've edited the blaster mount in this case to fit any universal blaster. I don't have any pictures for this just yet because I have not...
thingiverse
It will hold a Nerf StrongArm Blaster and possibly the older Maverick model, but I have yet to confirm this. It consists of three pieces that have to be glued together. Two straps will be needed to secure the holster. One around a worn belt and...
thingiverse
Remix of Hammershot holster by ADBARRERAS. Flipped for a lefty. ... https://www.thingiverse.com/thing:2488003
thingiverse
I was looking for a holster for my hammershot and couldn't see any here so i made one.
thingiverse
A holster style mount for my magnet holster design just put velcro straps or something threw it and bam a holster HARDWARE magnets...
thingiverse
This is supposed to work with clips and velcro and that come with holsters. Extra velcro strips are needed and go in the slots on the side. The SPAMF fits in by sliding it in at an angle. ...
prusaprinters
... with the blaster. once fitted, however, this holster is incredibly reliable. ...featuring the brand new SoxFoxDesigns logo. </p><p> </p><p>Photo included is of the old design (Beta) and was created before my brand was born. </p>
thingiverse
... made earlier. Printed in Orange PLA to match the color Nerf uses. I created this in Design Spark Mechanical. I sliced it with Simplify3D and printed without raft and support. ...The bottom of the print is totally flat so ideal for raffles printing.
thingiverse
You need to glue the clip into the divot in the holster for either and the clip is universal. The three bullet holder is modified from https://www.thingiverse.com/thing:38038 Please don't hate on it, I designed it in an hour in tinkercad so it's not...
cults3d
This is a fixed version of GMBridge's Star Lord Nerf Blaster Holster Clips. Right and Left Holsters are included. I had a problem with the original STL not having the vertical clip portions attached to the base. When printed these pieces would...
thingiverse
This is a fixed version of GMBridge's Star Lord Nerf Blaster Holster Clips. Right and Left Holsters are included. I had a problem with the original STL not having the vertical clip portions attached to the base. When printed these pieces would...
thingiverse
Although it would be difficult to make Nerf blasters that fold into such compact form factors automatically, we can still hold them on our backs, hips, anywhere, no matter how big they are. This design is a holster for blasters that do not fit in a...
thingiverse
original thing and missing parts: https://www.thingiverse.com/thing:255846 i dont have a 3d printer so i didnt test this probably needs support tho
thingiverse
A tactical addition to any fun office environment. Modified the STL to have a flat face for mounting on my desk cabinet. Mirror if you want to mount on opposite side. ... In case scale is off - X: 118.89 Y: 75.76