nexus 5 charging dock 3d models
595905 3d models found related to nexus 5 charging dock.thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1655546 Instructions Using the following options: phone_depth = 3 font_size = 7 TextLabel = Google connector_width = 11.1 phone_name = Nexus 5 connector_height = 19 connector_depth = 6...
prusaprinters
I designed this specifically for my new Nexus 5 phone but it should work with most other cellphones. I originally created this because the nokia charger is cheaper than the Nexus Orb (if you know where to look ). I wanted the angle but wanted to...
thingiverse
I designed this specifically for my new Nexus 5 phone but it should work with most other cellphones. I originally created this because the nokia charger is cheaper than the Nexus Orb (if you know where to look ). I wanted the angle but wanted to...
thingiverse
Wireless inductive charging stand for Nexus 5 (and probably 4) to be made with this :http://www.dx.com/p/zy-169-qi-standard-wireless-charging-transmitter-module-green-307276#.VEA4ifl_vs9
thingiverse
Edited the dock for the nexus 6 created by spavis to fit the nexus 5 and added a nexus logo at the front
thingiverse
My wireless charging dock that I designed for myself and now I'm sharing with you! Designed for a Nexus 5 and this wireless charger. ... Enjoy!
thingiverse
Instructions Install 4 N48 1/2 by 1/8 inch neodymium magnets (such as these) and a QI charging PCB (I think I ordered this one, but I don't quite remember), and then place in a normal car dock. Plug in the charger and just set your phone on the...
thingiverse
A DIY Qi wireless charging dock designed for the Nexus 5. This may work fine with other phones but the measurements for this are made to hit the "sweet spot" on the Nexus 5 for wireless charging. ... This is the Qi module I used, however many...
prusaprinters
I designed this specifically for my new Nexus 5 phone but it should work with most other cellphones. I have also added an "all one part" version that is more home printer friendly with supports to help with the bridging. Check out the portrait dock...
thingiverse
I designed this specifically for my new Nexus 5 phone but it should work with most other cellphones. I have also added an "all one part" version that is more home printer friendly with supports to help with the bridging. Check out the portrait...
thingiverse
Charging dock for Nexus 6P with carrying case on. Fits the original Type-C power cable. ...Update: v 3.1 is 1mm deeper to accommodate thinker case.
thingiverse
Nexus 6p Charging Dock A simple, dock with a nice snug fit for the Nexus 6P and OEM charging cable. The crossbar in the back prevents the cable from flipping the whole thing over. Never mind those holes in the back. They're a vestigial remnant from a...
thingiverse
Laser-cut charging dock for your Nexus 7 Instructions Make your own Nexus 7 charging dock for $15 Do you have a super sweet new Nexus 7, but don't want to leave it laying around? This laser-cut dock will help protect your tablet and keep your...
thingiverse
This dock uses the original Nexus 5X charging cable. Just push the cable through the hole and use the clip to hold it in place. Everything is friction fitted. There are two versions: The naked version is for phones without any case and the other...
thingiverse
... Nexus 6P STL Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: Doesn't Matter Supports: No Resolution: 0.25 Infill: 10-20% Notes: Perimeters: 3+ To ensure connector will fit through, make sure your XY dimensions are tuned in.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1655546 Instructions Using the following options: support = 0 phone_depth = 4.5 font_size = 9 TextLabel = extraD = 0 connector_width = 12.2 phone_name = Nexus 6P offset = 0 connector_height =...
thingiverse
Nexus 5 dock for wireless charging (you will need electronics from real charger)
thingiverse
The Nexus 4 wireless charging orb has a design problem, after a while the phone just slides right off as dust builds up in the rubber ring. There are two other docks out there on Thingiverse to solve this problem but I found them to be too bulky for...
cults3d
This is a adapter/ stand for my MOYI T-200 wireless charger, the goal was to have a charging station for my Google Nexus 4 cellphone (including protection case) with a wireless charger.
thingiverse
This holds a Koolpad charging pad (https://www.amazon.com/KoolPad-Wireless-Charging-compatible-SlimPWRcard/dp/B00DQDE1K8) and a Nexus 7 (2013) tablet to mount on a wall or nightstand. ...The original design is at...
thingiverse
This is a adapter/ stand for my MOYI T-200 wireless charger, the goal was to have a charging station for my Google Nexus 4 cellphone (including protection case) with a wireless charger. ... Instructions I designed the charging adapter with two parts to...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1655546 Instructions Using the following options: connector_height = 19.9 phone_name = Nexus 6 phone_width = 90 TextLabel = Google font_size = 9 connector_width = 10.5 connector_depth = 6.8...
grabcad
Hello everyone, I just joined this community and wanted to share with you a design I came up with for a Nexus 5 cellphone. I included the Android and Nexus logos in the design. The design of the logos are the property of Google, but I came up with...
thingiverse
This is a charging dock with a hook for the dimensions of the nexus 5. The hook is 1 in. ...long so it could fit the railing of my bed.
thingiverse
This is a Nexus 7 Dock, with USB charging. It also has a guide for the Nexus 7 to slide into the dock. Instructions Print out 1 of each of the items. The USB holder connects at the bottom as shown...
thingiverse
This is a remix of my nexus 5 charging car dock after my original distorted in the summer heat in my car (Printed in PLA). Modification since V1: 1:Designed for slimmer "shell" cases like the Capdase Karapace Touch. 2:Designed for ABS for heat...
thingiverse
I wanted to build a dock adapter for my Nexus 5 that would clip into the standard receptacle of my existing GorillaPod SLR (the largest size). Nexus 5 fits great, but the tab doesn't lock into place in the tripod. Fortunately, the friction on the...
thingiverse
Loosely based on the Nexus 6P Dock - No Casehttp://www.thingiverse.com/thing:1137852 Also used the NEXUS logo from Nexus 5 Dock with Charginghttp://www.thingiverse.com/thing:1149587 Spigen Rugged Armor Case on...