nf atacr 1 8 3d models
1035978 3d models found related to nf atacr 1 8.
cgtrader
Game ready model of a Nightforce ATACR 1-8x24mm Low Power Variable Optic. A mount has not been included with this scope, if you need one I have provided one for free here: ...
cgtrader
The SVL rifle (Lobaevs sniper rifle) is in service with the security services of the President of the Russian Federation. ...Also the operator of this rifle are the United Arab Emirates, in this country the weapons were produced by a unit of TADS...
cgtrader
The SVL rifle (Lobaevâs sniper rifle) is in service with the security services of the President of the Russian Federation. Also the operator of this rifle are the United Arab Emirates, in this country the weapons were produced by a unit of TADS...
thingiverse
These are replacement fan blades for an 8 inch desk fan. ...These have been designed to be compression fit to a 6mm fan motor shaft. The design was inspired by the Noctua NF-A12x25. ...Fewer blades have been used to reduce the weight.
thingiverse
CR10 NF-TC-01 NF-TC-02 Sovol 2 in 1 Hotend Mount
thingiverse
Le iniziali di un amico e di sua moglie. Da tenere in bella vista nella loro casetta sul lago. Pezzi s-montabili e ri-montabili, per le serate dove proprio no sai che fare... ... Instructions Ti...
thingiverse
**"Cyclops NF 2-in-1"** aka **"LERDGE 2-in-1 V2"** (slightly different screws) as model: helps you to mock new combinations; e.g. I modeled it as I wanted to adapt my **parametric part cooler** with 50x15 fan blower (only use with silicon nozzle...
thingiverse
... Engineering Computer-1 case. ...The case is designed to install only one case fan but I wanted to install 2 fans - intake and exhaust, so I came up with a fan mount idea to install Noctua NF-A4x20 as an extra fan. ... Form 2 | Grey Pro v1 | 0.1mm
thingiverse
Is a mount for bltouch and nf sunrise 1.2 extruder in ender 5 with top linear guide mod. It is mobile, you can adjust the bltouch heigh for volcano o another block. ... For more stability use 3 insert m3 and 3 screw (2 for fix mount and one for fix...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=767317 Instructions Using the following options: bearing_h = 7 bearing_d = 8.1 max_d = 72 min_d = 40 $fs = 1 $fa = 1 rod_d = 8.1 cone_h = 20
thingiverse
Customized version of http://www.thingiverse.com/thing:84882 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=84882 Instructions Using the following options: thickness = 4 diameter = 60 tol = 1 parts = 8 fine = 50
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=113015 Instructions Using the following options: Build_Plate_Type = 0 ring_width = 5 Build_Plate_Manual_Length = 100 center_radius = 6 number_of_rings = 2 ring_height_step = .5...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=113015 Instructions Using the following options: pin_cap_gap = .45 pin_cap_width = 4 Build_Plate_Manual_Length = 100 number_of_electrons = 79 ring_height_step = .5 mesh_resolution = 70...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: thread_step = 2 outer_diameter = 14 nut_type = normal drive_diameter = 2 thread_outer_diameter = 10 head_type = socket slot_width = .20...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=651475 Instructions Using the following options: angle = 20 outerDiameter = 220.0 aperture = 203.0 centerHoleDiameter = 40 tol = 0.1 maxBars = 10 mHeight = 4.0 section = 1 bHeight = 8.0 sections...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=113015 Instructions Using the following options: pin_radius = 2.45 Build_Plate_Manual_Length = 100 ring_spacing = 2.5 number_of_electrons = 79 number_of_electrons_on_ring7 = 1...
grabcad
Valvula solenóide Mola 24VCC 1-4NPT 3 Vias NF Ref. ...N18.3822 Werk-Schott
thingiverse
An adapter I cobbled together in Tinkercad for mounting a NF TC-1 dual extrusion hotend on your ender 3.
grabcad
Noctua NF-A20 - Computer Case Fan------------------------------------------------------Diameter: 200 mm, Tickness: 30 mm170x170, 154x154 and 110x180 Holes------------------------------------------------------outer dimensions not accurate also drill...
thingiverse
Interchangeable plate for 3dsway NF NC-01 2 in 1 dual extruder, or Chinera / Cyclops, and 18 mm auto-leveling probe, with back holes for allen key setting's of the height.
thingiverse
... If you have questions, please ask me and I will help as much as possible. Additional Hardware: - 5 M3-8 screws for mounting bracket 2 to the hotend and 2 to mount bracket 1 to ender 3 plate. - 1 M3-6 screw for mounting bracket 2 to bracket 1. ...
thingiverse
Features: * Orbiter 1.5 mounted on a minimal plate on top of the carriage * NF Crazy mounted in the V6 locker * 4010 hotend cooling fan * Dual 4020 fans for cooling (fan ducts are designed to support up to 4CFM flow) * Neopixel 16 LED ring (entirely...