numark pt01 cartridge 3d models
8237 3d models found related to numark pt01 cartridge.youmagine
In stock condition, the Numark PT01 platter is quite flexible due to a design flaw. ...This part is intended to strengthen the Numark PT01 platter.
thingiverse
Loosing or breaking the tonearm clip of your NUMARK PT01 USB or PT01 SCRATCH portable turntable is a pain. ...That's why I decided to share this 3D file to make it easy for you to replace it.
youmagine
Tonearm Holder for the Numark PT01. Either to put the tonearm onto it while You change records, and also for locking the tonearm in place for transport. ... Place the toneram holder anywhere You want with a strip of double-sided adhesive tape.
youmagine
Little plastic inserts to serve as replacement for those little felt pads, as to be seen on my "PT01 Righthand" build. ... Two versions, with or without recess.
youmagine
7 Inch Record Adapter for the Numark PT01 Higher than the stock part.
thingiverse
I have a distracted friend....which has lost its battery cover for the Numark PT01 Scratch...
youmagine
This device enables to store up to seven 7" records inside the Numark PT01 top cover. Print with 100% infill. Glue the parts to the PT01 cover, use the largest 7" cover that You got as a blueprint. Get a decent rubber band. ...Enjoy
youmagine
Building this project will get you a Bluetooth/SD Card/USB reader module built into your Numark PT01. My primary use case is to allow the looper app on my mobile to stream its audio without a 3,5mm cable to the PT01 (#lookMomNoCables!) But is also...
thingiverse
Little leg to use the cover of Numark PT01 Scratch as Stand! ... U need four pieces of this
myminifactory
I created a spindle record clamp for my Numark PT01 because I wanted to travel with it and not have to carry around a 7" record in my bag. I printed it on my Form 2, so the tolerances were tight. ...Haven't tested the long term viability.
thingiverse
leg to use the cover of Numark PT01 Scratch as Stand! ... U need four pieces of this
thingiverse
Adaptor to convert original PT01, PT01-USB and PT01 Scratch ceramic snap-in cartridge to a regular style magnetic cartridge mount with screws, specifically when swapping the tonearm for a 3D printed from Beatshelter, Jesse Dean or Bihari. ... It will...
pinshape
I created a spindle record clamp for my Numark PT01 because I wanted to travel with it and not have to carry around a 7" record in my bag. I printed it on my Form 2, so the tolerances were tight. ...Haven't tested the long term viability.
thingiverse
I created a spindle record clamp for my Numark PT01 because I wanted to travel with it and not have to carry around a 7" record in my bag. I printed it on my Form 2, so the tolerances were tight. Haven't tested the long term viability. Print...
thingiverse
Adds extra stability to your PT-01 for the portablist scratch sessions. This ingenius accessory minimizes platter wobble and gives a sturdier feel for the best possible performance when cutting on PT-01 turntables. ...Super easy installation, engineered...
youmagine
This little bracket is intended to hold the relais board that comes with the available "Start/Stop button kits" for the Numark PT01, in the place where the old switch board" was stored. ... (requires two M3x16 countersunk head plastic screws)
youmagine
"Spraycan Cap" Casing for the Jesse Dean Designs "Record and Mat Spindle Holder" rubber. Better handling when removing the rubber part from the platter pin. ...Just stuff the JDD rubber part inside the printed part, that's it.
grabcad
when i mixed, i used thisnow it is to old modelscan be see herehttps://www.numark.com/product/omnicontrol
youmagine
"Spraycan Cap" Casing for the Jesse Dean Designs "Record and Mat Spindle Holder" rubber. Better handling when removing the rubber part from the platter pin. ...Just stuff the JDD rubber part inside the printed part, that's it.
thingiverse
It is a knob for PT01. ... http://faderlab.cart.fc2.com/ca21/48/p-r-s/ I sell it here.
grabcad
Numark Mixtrack PRO II is a DJ Controller. I own one, and I tried to replicate it in Catia V5 on scale 1:1 This is the result :D I attached also a STP file of the CATProduct merged in a CATPart. ...
thingiverse
These are al the buttons for the Numark NV II. I F'd up mine after i cleaned my controller. I've put a like a 100 hours into the designs to perfect them. And they al work! Only thing you need to pay attention to is the part thats touching the PCB...
thingiverse
Printed and verified that the holes aligned with the Numark PT01. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/5Hxnr2FdNfY
thingiverse
This is wendz replica of original platter for turntable and applied to PT01 platter. This is just some butter to the bread! Print as per your preference (infill, color etc.) The size is exact but i build for higher and lower types. ... Enjoy and keep...
thingiverse
Tone Arm clip for numark ttx . ...will likely work for all tt series turntables ie tt500 tt200
thingiverse
Modelled a replacement tonearm clip to use on a Numark TT1650, as I bought a pair of turntables and one clip was missing. Pretty simple process for this part - - Slice and print one side - Mirror, slice and print the other side - Attach...