odroid hc2 3d models
458 3d models found related to odroid hc2.thingiverse
I updated my Odroid HC2 from a 3.5" disk to a SSD and needed something to hold the SSD in place.
thingiverse
A two-part cover for the ODROID-HC2. Similar in design to the official one, but sturdier. With this cover, you can pick up the HC2 by the cover without the bottom falling out. ... Print both parts with support structures.
thingiverse
This is a remix of the Odroid HC2 fan shroud. I have printed this and it is working. it fits more tightly around the drives and the sides of the enclosure forcing more air across the drives. ... It is designed to mount a 120mm fan to a stack of 4...
thingiverse
Blade rack for Odroid HC2 units. I used 3 x Mean Well 12 V (DC) 150 W LRS-150F-12 to power the units. Will update with more build instructions later. It was designed to hold 9 HC2's with 2.5" drives. Probably easy to adapt to 6 HC2's with 3.5"...
prusaprinters
This is a remix of the Odroid HC2 fan shroud. I have printed this and it is working. it fits more tightly around the drives and the sides of the enclosure forcing more air across the drives. ...It is designed to mount a 120mm fan to a stack of 4 Odroid...
thingiverse
I purchased some Odroid-HC2 SBC's to use as a NAS, only to discover that they run fairly hot. I designed this fan mount to add a 120mm fan for cooling a stack of 4 HC2's while remaining fairly silent. It slides over the aluminium cover, and the...
thingiverse
This is my solution to mount my homeserver on the wall. ... You need 4x hexagon screw M3 x 20 (DIN 912 A2) to mount the plate on the cases
thingiverse
Just a quick remix from the original, a lot more substantial and ok to hold a 2.5" HDD or SSD. You need to print two of those. ... And it does fit with the lid!
thingiverse
Customized version of https://www.thingiverse.com/thing:2850939 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2850939
thingiverse
I made this for a friend of mine who noticed his Fibaro HC2 was running hot. ... The grill replaces the side panel on the Fibaro and allows the heat to dissipate adequately to reduce the temperature considerably.
prusaprinters
This is a box for an ODROID C2 case. ...It is designed for an 80mm fan. For the HDMI port, there is no hole in the case, ODROID is used as a server.
grabcad
Odroid C2 (Thanks to jeneaf) I updated the C1 into the C2 with an eMMC in position. ...Solidworks 2013.
grabcad
ODROID-X2 open development platform is based on Exynos4412 Prime 1.7GHz ARM Cortex-A9 Quad Core with 2GB memory
grabcad
Made for cases design and any other fine application.ODROID-XU4 is a new generation of computing device with more powerful, more energy-efficient hardware and a smaller form factor. Offering open source support, the board can run various flavors of...
grabcad
... 4.4 KitKat and 5.0 Lollipop. By implementing the eMMC 5.0, USB 3.0 and Gigabit Ethernet interfaces, the ODROID-XU4 boasts amazing data transfer speeds, a feature that is increasingly required to support advanced processing power on ARM devices.
grabcad
This is a rough sketch up of the Odroid U3. The main board is accurate but the components are all done to with +/- <0.25 mm tolerance. ...If you require other formats or more detail just ask I will improve it with time but this is all I need...