oil filter crusher harbor freight 3d models
43372 3d models found related to oil filter crusher harbor freight.thingiverse
Threaded plug for the Pittsburgh Automotive (Harbor Freight) 5 gal oil drain dolly. The threaded plug closes the telescoping drain tube hole so you can take the 5 gallon container to the auto parts store to recycle the oil without worrying about the...
thingiverse
This breather/filter was made for the Harbor Freight 10 gal. 2.5 HP Air Compressor. https://www.harborfreight.com/10-gal-25-hp-125-psi-oil-lube-air-compressor-69092.html Has threaded cap instead of snap on. ...Thread is 1/2-14 Here is a smaller...
thingiverse
Designed to replace the intake air filter box on the Harbor Freight (Central Pneumatic) 21 gal. ...2.5HP 125PSI air compressor.http://www.harborfreight.com/21-gal-25-hp-125-psi-cast-iron-vertical-air-compressor-61454.html
thingiverse
This breather/filter was made for the Harbor Freight 10 gal. 2.5 HP Air Compressor. https://www.harborfreight.com/10-gal-25-hp-125-psi-oil-lube-air-compressor-69092.html Has threaded cap instead of snap on. ...Thread is 1/2-14 This is a smaller...
thingiverse
From poire's model, I took off the threaded portion and added the appropriate size for the Harbor Freight Central Pneumatic 40400 air compressor. The threads measure 19.2 mm (0.756 inches) outer diameter, with 1.5 mm thread pitch. Could not figure...
thingiverse
Go Kart Air Filter Adapter The air filter came from ebay. It is cone shaped, like the ones used on motorcycle engines. ...Search for the following: 54mm Tapered Air Filter, or K&N RC-2340 STL STP DXF PDF
myminifactory
Imported original part, split it, added the baffles similar to that of a muffler to cut down on the noise on the intake of the air, then put back the part and alignedMight design a removable cap later on (or someone could remix) so foam material...
thingiverse
Imported original part, split it, added the baffles similar to that of a muffler to cut down on the noise on the intake of the air, then put back the part and aligned Might design a removable cap later on (or someone could remix) so foam material...
thingiverse
I found that if I hammered it on well enough there was no need of a set screw. ...If you have different results I included a model with a hole for a set screw as well
cults3d
I made these for the Harbor freight featherboard. ...The original inserts do not fit the Harbor Freight 10" table saw so I made new ones.
thingiverse
A box and lid to securely hold set of Harbor Freight Probes. ... There is a remix that is a box for mini files from Harbor Freight as well.
thingiverse
I made these for the Harbor freight featherboard. ...The original inserts do not fit the Harbor Freight 10" table saw so I made new ones.
thingiverse
I think this is the medium size vice from Harbor Freight best printed out of TPU.
thingiverse
A stand for a Harbor Freight Multimeter. ... I added some pockets for magnets to the stand.
grabcad
A stand built from 80/20, Inc. ...components for my Harbor Freight Shear, Brake & Slip Roll unit.
thingiverse
Similar to other designs but I wanted something a bit thicker and different sizes. ...These work with the Harbor Freight box's
thingiverse
This is a way to add an 18650 to the free Harbor Freight LED, the voltage is close enough to 3 AAA that you can just switch out.
thingiverse
Quick socket organizers I made for harbor freight deep well socket sets. I've included a file for both SAE and metric sets. ...
thingiverse
Replacement slide on 3/8 drive socket holder insert for the Harbor Freight magnet organizer. ...Friction fit rather than ball bearing snap but it works fine.
thingiverse
This is a red diffuser for a Harbor Freight flashlight. I needed to use my flashlight at night while keeping my night vision. ...
grabcad
Modeled this mini mill we purchased fron Harbor Freight. Modeled in Solidworks 2013 and rendered in Keyshot 4. ...Solidworks 2013 files
thingiverse
Couldn't find any model of a Harbor Freight Apache Series case so decided to start creating them from scratch. ... This is the Apache 1800 case.
cults3d
Quick socket organizers I made for harbor freight deep well socket sets. ...I've included a file for both SAE and metric sets.
thingiverse
This is a replica of the harbor freight 4x8 trailer. Unsure of how to do the conversion for scale, but 1mm=1inch. ...
thingiverse
This is a coupling to take two Harbor Freight Pittsburgh Ratcheting Clamps and make one long one. ... Full details are in this video: https://youtu.be/GAi69ihmOHE
thingiverse
... ... printed with the flat side down. designed to be affixed with a 3m command strip. harbor freight screwdrivers like this have really poor quality control so you may need to clean up some plastic over-molding on the screwdriver to perfect the fit
thingiverse
This is a holder screws to the wall to fit a small flashlight from harbor freight (those free ones with the coupon). ... We used it for placing emergency flashlights near our entrances and on our powder coating setup.