olight bike mount 3d models

It's a combined GoPro and Olight Baton S35/S65 mount, primarily designed to be kept by two bottom screws of Cannondale stem, looks perfectly with Lefty fork but might also fit to classic ones. Support is advised for main part due to considerable...

Mount was Designed for Olight S1R Torch but will work with similar models. It has been tested on mountain bike for few hours and stayed still.  Internal diameter is 35mm with groove inside to stick some rubber for better grip. ... Needs M3 Bolts and...

... so I modeled this thing. ...attaches with zip ties and a little square of double stick tape. I designed it to glue in an 18x5 mm magnet in the base, though the clip keeps it pretty solid. Still putting my bike together, but will update when its done.

... so I modeled this thing. ...attaches with zip ties and a little square of double stick tape. I designed it to glue in an 18x5 mm magnet in the base, though the clip keeps it pretty solid. Still putting my bike together, but will update when its done.

I was tired of the vertical mount so I designed this one, it mounts to the seat post horizontally. ...It's not perfect but it works, Feel free to remix it.

I was tired of the vertical mount so I designed this one, it mounts to the seat post horizontally. ...It's not perfect but it works, Feel free to remix it.

This is a mount for [Olight Perun Mini](https://olightworld.com/olight-perun-mini) and [Olight S2R-II Baton](https://olightworld.com/olight-s2r-baton-ii) flashlights. This mount is for non-metallic surfaces that the flashlight's magnetic tail cap...

This is a bike handlebar mount for S2 with the idea that lamp can be powered from external battery. Just print the parts, remove back cover and battery from S2 and screw everything together. The negative wire should be connected under the screw in...

This is a Strap Mount for the Olight Gober. ...You can use it with straps from backpacks or with double sided velcro tape.

Simple wall mount for any Olight flashlight that uses the magnetic charger. Tight press fit at the top (needs to be sanded slightly). ...Dimensions: 33x61x45 mm

This is a mount for Olight Perun Mini and Olight S2R-II Baton flashlights. This mount is for non-metallic surfaces that the flashlight's magnetic tail cap cannot attach to directly. To mount a flashlight vertically, a metal disc or magnet needs to be...

This flashlight mount is made specifically for the Olight Baton 3 The mount might dig a bit into the blaster when mounted. This will NOT work with picatinny. The flash light is magnetically mounted, making use of the magnetic charging ports and 4...

Simple mount for Olight flashlights or anything with a 19.5 / 20mm diameter Designed to mount my Olight H1R NOVA to my helmet I uploaded 2 versions, 1 with a flat base and 1 with a slightly curved base (i had to sand it to make it fith my helmets...

https://www.thingiverse.com/thing:4649420 based on wall mount olight charger.Clips to the air outlet of car, slot the charger in (probably need to sand a little have it very tight fit)printed .2 on ender 3 prouse supports 

If you are looking for an aesthetic solution to that problem, then let me present to you my gel switch mount. It attaches to any RIS rail, so you can choose whatever location is convenient. I designed it for the OLIGHT gel switch, but a few others...

Hardware Used: DIN 933 M5x45 Hex Bolt, Qty:1, https://www.mcmaster.com/#91280a244 DIN 934 M5 Hex nut, Qty:1, https://www.mcmaster.com/#90591A260 (I used a GoPro nut and bolt from my bar mount kit. But pretty much any M5 hardware will work.) Note:...

This is a light mount that using Garmin edge optional mount. ... If you have Garmin edge series cycle computers, you may have some garmin mount and this spacer needs it. ... But this doesn't need any glues and screws.

Mount your Olight Baton Pro on your bike. ... Update 15.08.2020: a) New design for stronger hold (v10) b) New version for the Xiaomi Ninebot 1S Scooter (1s)

This is a Print In Place bike mount for the Olight H1R headlight. I wanted to make one that requires no other hardware. I would definitely use Supports. ...I would also recommend using PLA.

Waall mount option for Olight Warrior Mini - non charging

Olight mount + mlok to picatinny rail = HUGE My design fits the new Olight sROD-7 High/Low button remote switch and mounts it directly to mlok rail. no need for picatinny rail adapter and giant Olight mount. ... (Second picture shows differentce...

My newer I3E EOS mini challenged me, to create the equipment - to mount and remove it on my Giro Bike helmet. I am in retirement, time is not a problem, so I created a thing with Fusion360. You print it perhaps with 40%Infill, you'll need 1M4 nut...

It was made so that it could be mounted and hung on the wall to clear up counter top space. I installed it on the wall next to an outlet so that it could be charged while the flashlight is hanging. I designed it to somewhat look and match some of...

This is a simple flashlight bracket to mount an Olight i3t eos (great EDC flashlight) to my glasses.  It is small enough to keep on my keys for when I need it so I can always use my flashlight hands free. ... The mount is robust enough to...

The idea came from Olights new L Dock but instead of docking the flashlight upside down like theirs I designed it right side up. I also didn't want something that would take up space on a counter top so I came up with this design. As I started to...

This is a simple wall mount for the Olight Seeker 2 pro.

A flashlight mount for the I3T EOS (Olight) and the Weihrauch air rifle.

made this mount for my Olight I3T EOS to fit onto a mlock hand guard. ...pretty simple i reccomend printing it on the side for maximum strength.

A charging or just a mount for the Olight M2R Warrior Pro. ... by playing aroundg with color changes, also "glow in the dark" is a litte gimmick ;-)

A charging or just a mount for the Olight M2R Warrior Pro. ...by playing aroundg with color changes, also "glow in the dark" is a litte gimmick ;-)