orbiter v2 3d models
102448 3d models found related to orbiter v2.thingiverse
Sharing my Toolchanger mounting base for the new Orbiter v2. It has a slightly different mounting pattern, and I added a mounting point for tidy wiring. Mounting points for the extruder are sized for fitting 4.2mm diameter brass M3 inserts. ...
thingiverse
This is mount for Orbiter V2.0 for TwoTrees Sapphire S printer. Carriage screws - OEM. Orbiter screws - M3x10 = 2 pcs I first designed without wire holder, but then I designed V2 with wire holder. Look files. Print with any PLA or PETG with 100%...
thingiverse
......I don't have an Orbiter v2 to reference yet. Dimensions were based on what I could roughly get from the Fusion 360 Viewer file. The threads for the filament exit guide and the filament tensioner are just best guesses. This has not been tested by me.
prusaprinters
I needed a simple option for strain relief on my custom print head using an Orbiter v2 extruder on my BLV MGN Cube and this is what a few minutes of CAD got me. BOMM3 Heatset Insert [x2]PrintingPrint should be oriented the...
thingiverse
V2 has a little bit different holes, remix that centers it above hotend better. ... See pictures to understand what holes are used for mounting.
cults3d
V2 has a little bit different holes, remix that centers it above hotend better. ...See pictures to understand what holes are used for mounting.
thingiverse
This is a mount to use the Orbiter V2 direct drive on a Two Trees Sapphire Pro or SP-5.
thingiverse
This part allows the installation of the Orbiter V2 extruder on Ender3 V2's tool head. Additional parts required: <ol> <li>4x M3x16mm bolts</li> <li>2x M3 nuts</li> </ol> See the attached picture for the correct orientation of the part while...
thingiverse
More information you can find on our brand new website: [www.orbiterprojects.com](www.orbiterprojects.com) [The true story of the Orbiter v2.0](https://orbiterprojects.com/the-true-story-of-orbiter-v2-0/) You can read about the challenges we faced...
thingiverse
Plate to mount Orbiter v2 extruder on Wanhao D6. ... Requires 2 M3 heated inserts (M3x5x4) and a small piece of teflon tube (4mm OD, 2mm ID) Printed mine in ABS.
thingiverse
Parts printed and tested to mount the orbiter v2.0 on the afterburner extruder used expetially on Voron printers Uses 2x M3x20mm to hold the Chain_support_holder and the Extruder_holder Uses 2x M3x16mm to hold the Chain_support Uses 4x M3x8mm to hold...
thingiverse
Orbiter v2.0 mount should work with any ender 3 style mounting bracket and any style duct as long as it's NOT higher than the ender 3 style mounting bracket. Also mounting holes next to orbiter for an Adxl345. ...Remix of "The Original Speed Drive".
thingiverse
This is a bracket for the orbiter v2 to mount to the ender 5 with a e3dv6 hotend. It is designed to accommodate the generic e3dv6 adapter and the 3010 parts cooling duct. ... x_offset: 25.42 y_offset: 28.51
thingiverse
Adapter for connecting the Orbiter V2.0 extruder to a V6 / Mosquito / Dragon hotend in a BLV printer with an E3D V6 holder. 2 versions available: with M10 / 0.9 and M10 / 1 metric ISO thread. ... BLV Head holder:...
thingiverse
This is a support for direct-drive Orbiter v2.0 on TronXY X5SA-400 (but others X5SA should be the same). I rebuild from scratch this support because existing models do not fit exactly. Worked on weight gain, alignment of everything, a little stud on...
thingiverse
I wanted to mount my Orbiter V2.0 to my HEVO. This is a simple adapter that allows you to mount the Orbiter to the top of the Precision Piezo Orion. I modelled it for square nuts but you could probably use regular M3 nuts. I made it a bit big for...
thingiverse
This is my attempt to mount Orbiter V2 on KP3S Pro. Since KP3S Pro has slightly different than KP3S, I thought I cannot use already existing KP3S mounts. BLTouch offset : x_offset: 29.50, y_offset: 5.50 You may need spacer for it to optimise...
thingiverse
Also fixed some mistakes and tolerances I upgraded to an Orbiter v2 extruder and didn´t want to buy a new filament sensor. You´ll need some M3 screws (I had a few lying around here, I didn´t measure it, but once you print you can figure it out. ...
thingiverse
Here is my initial attempt / draft of parts required to mount an Orbiter V2 and Phaetus Rapido on an FLSun SR effector plate. You will need to enlarge the centre hole of the SR effector plate to a diameter of 23mm. In the absence of a step drill...
cults3d
This is a mount to attach an LDO Orbiter v2.0 to an SE300 hotend found on SeeMeCNC such as the BOSSdelta 300, 500, and Artemis 300. A few notes... Printing This will be best printed upside down with the top of the models on the build plate (see...
thingiverse
*** UPDATE: I've moved most of my designs to [Cults3D](https://cults3d.com/en/users/EtherBunny/creations) *** This is a mount to attach an LDO Orbiter v2.0 to an SE300 hotend found on SeeMeCNC such as the BOSSdelta 300, 500,...
thingiverse
The main features are: - Filament Runout sensing - Filament auto loading - Button for filament unload [Click here to join our Facebook support group!](https://www.facebook.com/groups/705637896767655) Detailed description you can find on my official...
thingiverse
Printable ender3 direct drive upgrade compatible with Orbiter V2.0 Extruder.
myminifactory
[EN]direct drive support for orbiter v2 and dragon hotend (rigide mount) for hypercube carriage. ... [FR]support pour extrudeur orbiter v2 et buse dragon de chez tiangle lab en fixation rigide pour chariot hypercube.
thingiverse
Made for my Ender 3 V2, should work perfectly on Ender 3 / 3 Pro except the extra hole will not be correctly aligned with the hole in the gantry plate. Currently used with a Satsana remix duct with a 5015 fan. Might replace with something even...
thingiverse
It uses 4x M3 inserts: -- Duct - one for the 5015 blower -- Duct - another to fix the orbiter mount -- Orbiter holder will need another two inserts to fix the Orbiter itself. The orbiter holder has a hole to add a guide of 10x1.8mm that you can...
thingiverse
Adapter for Two Trees Sapphire Pro or Plus for mounting the Orbiter V2.0 extruder You need - 4 cylinder head screws M3 x 10mm - 2 leans head screws M3 x 12mm - 2 M3 nuts - 1 cable ties