original prusa i3 mk2 3d models

Solid model of the Original Prusa i3 MK2 3D printer. Original Design is by Joseph Prusa Jr. and all parts are under the GNU GPL v3 License. ...If you just want the STL files to print them, they can be found at the original source here:...

Tool rack for Original Prusa i3 MK2

Mount for Logitech C920 on the z axis on Original Prusa i3 mk2

A model of the Original Prusa i3 MK2 https://www.tinkercad.com/things/aITVmlXl4xx-3d-printer-prusa-i3

Updated version of y-corner for Original Prusa i3 MK2 (using supports) Print Settings Printer: Prusa i3 Original Rafts: Doesn't Matter Supports: Yes Infill: 50%

Another Filament Guide for the Original Prusa i3 MK2, it has an 1,75mm opening on one side to slide the filament in or out.

This is a Pen holder for the Original Prusa i3 MK2 3D Printer. ... You can use it to do 2D Plotting or Circuit Board drawing for PCB etching.

... on 1 layer thin raft as the balls doesn't stick well to the bed. The rest of the parts are printed without support or raft. Print Settings Printer Brand: RepRap Printer: Original Prusa i3 mk2 Rafts: Yes Supports: No Resolution: 0.2 mm Infill: 20%

Print Settings Printer: Original Prusa I3 MK2 Rafts: Doesn't Matter Supports: Yes Resolution: 0.3 or 0.2 Infill: 85%-100% Notes: This is what I've had luck with. Print at whatever setting you feel like. ...Approximate dimensions Length: 242.5mm Width:...

Summary Clips on original holder to support shaft of any kind :) I revised it a touch so it slopes down towards the original holder Print Settings Printer: Original Prusa i3 MK2 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 15-20 Notes:...

Clips on original holder to support shaft of any kind :) I revised it a touch so it slopes down towards the original holder Print Settings Printer: Original Prusa i3 MK2 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 15-20 Notes: simple

Wanted to reduce the noice of my already super quiet Original Prusa i3 MK2, the hotend fan is the one thing makeing most of the noise now, so I designed an adapter/tunnel for the extruder to be able to mount a 40x40mm Noctua fan instead. ... Here is a...

A model of the Original Prusa i3 MK2 https://www.tinkercad.com/things/aITVmlXl4xx-3d-printer-prusa-i3 Print Settings Printer Brand: LulzBot Printer: TAZ 5 Supports: Yes Category: 3D Printers

Print Settings Printer: Original Prusa i3 MK2 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 20% Notes: It can be printed without supports, but if you're slicer settings aren't dialed in, you'll get curling on the overhangs with the...

... it works. I've measured the temperature of the heatbreak before and after the mod. It's about 5°K higher as with the original fan. Print Settings Printer Brand: RepRap Printer: Original Prusa i3 MK2 Rafts: No Supports: No Resolution: 0.2 Infill: 15%

This is a quick addition to the stock spool holder that comes with the Original Prusa i3 Mk2. The stock in itself is not exactly a secure spool holder, and it won't hold some spools (Taulman's 1kg spools for instance). This rod will enable you to...

I really like my original Prusa i3 MK2 a lot. However, the spool holders are not my favorite solution. So I just created my own. My part is quite a bit thicker than the original part and instead of using integrated plastic bolt stubs, it just has...

This is a simple bed test for Original Prusa i3 MK2. Run it after "V2Calibration.gcode" to ensure your first layer is perfect across the whole print area. The STL prints in one layer and allows you to easily fine tune your machine using live adjust...

... of the mount. I have not had the opportunity to mount it yet, that will come after I figure out the wiring and firmware side of things. Print Settings Printer: Original Prusa i3 MK2 Rafts: Doesn't Matter Supports: Yes Resolution: 200 Infill: 30

...Print Settings Printer: Original Prusa i3 MK2 Rafts: No Supports: Yes Resolution: .20 Infill: Solid & 30% Notes: Underbed parts and camera housing were printed in PETG with solid infill @ 240c, y-Bar was printed in Hatchbox PLA with 30% infill @ 210c

This is my version of an LED Lamp mounted on an Original Prusa I3 MK2 3D Printer, printed in PLA. Electronic Components: Adafruit Pro Trinket - 5V 16MHz controller powered via a micro USB cable.https://www.adafruit.com/products/2000 Individually...

This is my version of an LED Lamp mounted on an Original Prusa I3 MK2 3D Printer, printed in PLA.Electronic Components:Adafruit Pro Trinket - 5V 16MHz controller powered via a micro USB cable.https://www.adafruit.com/products/2000Individually...

Prusa i3 LCD knob that was inspired by the Original Prusa i3 MK2. The dimension should be the same as the one that shipped with the MK2. I redraw it and get rid of the tab from the original one to make a cleaner look that fit my taste. For those of...

Small design PINDA protection. ...Print Settings Printer Brand: RepRap Printer: Prusa i3 MK2 Rafts: No Supports: No Resolution: 0.05 mm Infill: 10%

Two part tool holder for the Prusa I3 MK2/S that I created in Fusion 360. The first part holds pliers, hex keys, a screwdriver, and a multi-tool, and the second part holds sixteen nozzles, a spatula, and calipers. The second part sits on top of the...

This is an X-Brace that i made to ensure the M10 threaded rods are completely parallel on my Original Prusa i3's Y-Axis I print this laying flat on the bed. ...Print Settings Rafts: Doesn't Matter ...

A very simple spool holder. Two 608 ball bearings, one piece of 8mm threaded rod 4 bolds two washers one piece of 5cm PVC pipe insert ball bearings into two 3D printed parts, Then glue the parts into the PVC pipe And that's it It's the exact diameter...

Simplest and fastest-printing solution out there for the MK2 crappy reel holder (other reel dowels seem to be way thicker than necessary). Print with just 2 shells at default extrusion with of 0.45mm. Or heck, spiralize PLA with a nice thick layer...

I needed a quick and dirty way to attach my new Logitech c920 webcam to the bed of the Prusa. Lots of things to improve. ... Printed with eSun PETG.

Two 608 ball bearings, one piece of 8mm threaded rod 4 bolds two washers one piece of 5cm PVC pipe insert ball bearings into two 3D printed parts, Then glue the parts into the PVC pipe And that's it It's the exact diameter of Joseph Prusa's rolls. ... ...