paracord clips 3d models
98323 3d models found related to paracord clips.thingiverse
I use it to attach a first aid pouch so that it can be quickly removed by pulling out the bottom paracord loop and then pulling both clips at once by a loop in the top holds. They are best printed at 100% for strength and on their side. ... If there...
thingiverse
I shrunk it down a bit, so that hollowed out paracord (cut a length, pull out the core fibers) can be used as lanyard material, and then just bulked up the general design, adding a bit of strength, but mostly making it look a bit more polished in my...
thingiverse
Clip that was made to add a paracord handle to the side of the Javelin VSlinger bag from Vanquest. Coud be used to add paracord straps to any bag with 1 inch molle straps. ... Designed to have 4 passes of 550 paracord through it.
thingiverse
http://www.amazon.de/Gerber-Survival-Grylls-Paracord-GE31-001683/dp/B008FM04OC?ie=UTF8&psc=1&redirect=true&ref_=oh_aui_search_detailpage
prusaprinters
http://www.amazon.de/Gerber-Survival-Grylls-Paracord-GE31-001683/dp/B008FM04OC?ie=UTF8&psc=1&redirect=true&ref\_=oh\_aui\_search\_detailpage Category: Other
cults3d
========================== From original version (https://www.thingiverse.com/thing:613544): Print with supports, 10% infill, .2mm layer height. You will have to remove some of the supports from the lid. For best results, run a 3/16 drill bit...
thingiverse
Yet another remix, this time with slotted holes for zip ties or para cord. Shell thickness 1.2 or 1.6 is strong enough no need for 100% fill Make sure to print laying down as shown for proper strength. ... I print these on a brim as shown to keep the...
pinshape
This is a paracord holder. ...This holder should hold at least 25' of paracord.
thingiverse
... assist in winding and cleats on the size to hold the cord ends. The larger hole in the one arm can be used with a small carabiner to clip to something. It will hold about 40 feet of 2.38mm cord. ... Print flat for best strength and no supports.
thingiverse
I created this for Paracord Weavers that don't have the time to go out and buy an actual Paracord Fid.
thingiverse
Just a little paracord winder I designed after years of dealing with knots. Will hold up to 100 feet of 550 paracord. ...I just use PLA at 20%.
thingiverse
Ein Anhänger für ein Paracord Survival Armband. ...Eine Kleine Dose und ein Fach für Notgeld.
prusaprinters
A spool which holds about 75' of 5mm paracord. ...Could be scaled up or down to hold more or less cord. There is a hole in the center to thread the paracord through.
thingiverse
A paracord spool I designed. ...To fasten the ends I did an overhand knot through one of the holes and wrapped. Designed for Paracord 550, but works for similar rope.
thingiverse
This is a basic Paracord spool. Diameter 55mm. Only needs a 2 threads and threaded rod for complete. ...
thingiverse
A paracord bracelet clasp designed to look like a drive chain link. ...15mm inside, but should scale OK.
prusaprinters
A 25mm shackle(15mm inside) for paracord bracelets, but should scale OK. Borrows the ClickyBolt from my Thing here https://www.thingiverse.com/thing:2756547. Designed to be printed flat without support, thus the offset in the crosspin to allow a flat...
thingiverse
He used pieces of card board to wind paracord. This removes the issues with cardboard folding and wearing out. A ladder for winding paracord. This is the second revision with additional internal support ...
thingiverse
3d Print you own paracord lanyard, Just add a M3 6mm bolt and a mini carabina Blog post - https://wp.me/pKY3w-D5