paracord pulley 3d models
24447 3d models found related to paracord pulley.thingiverse
The pulley housing is designed to accept two loops of paracord that each pass through both halves of the housing, additionally holding the housing together and acting as a failsafe so that even if the 3D print fails, the paracord looped through the...
thingiverse
This is simple pulley for paracord. You can use it to create a zipline. Not intended for load. Just use 2x M3 x 18 bolts and 2x lock nuts. It can be set on a rope after the rope is tied. Print both parts twice to create one pulley. ...After print, heat...
cults3d
This is used for camping (eg) tarps, traps, food storage and anything else !Don't forget to check out my other designs, Enjoy ;)
thingiverse
This is used for camping (eg) tarps, traps, food storage and anything else !Don't forget to check out my other designs, Enjoy ;)
thingiverse
For the Double pulley print 2 of housing 3, 2 of housing 4, and 2 of the V-Rollers Hardware: SINGLE PULLEY (3 or 5) #10-32 x 1" screws (3 or 5) #10 nuts (3 or 5) #10 lock washers (6 or 10) #10 washers (1) 6001 bearing DOUBLE PULLEY (5) #10-32 x...
prusaprinters
6001 bearing size: 12mm ID, 28mm OD, 8mm thick. For a single pulley Print 2 matching housings and 1 V-Roller for each pulley. For the Double pulley print 2 of housing 3, 2 of housing 4, and 2 of the V-Rollers Hardware: SINGLE PULLEY (3 or 5) #10-32 x...
myminifactory
(Paracord as seen on Amazon: http://amzn.to/1gIiqlo) This design used 6 pulleys to divide my 170 lb body weight 6 times into roughly 30 lbs input force. It was strong enough but it was hard to balance! So I later designed the mount and center holder...
pinshape
(Paracord as seen on Amazon: http://amzn.to/1gIiqlo) This design used 6 pulleys to divide my 170 lb body weight 6 times into roughly 30 lbs input force. It was strong enough but it was hard to balance! So I later designed the mount and center holder...
thingiverse
According to my clevis calculator (available here: http://engineerdog.com/resources/) at 50% infill (ABS) this design is rated to withstand the 550 lb load that the paracord is supposed to break at. ...
thingiverse
Customized version of http://www.thingiverse.com/thing:363800 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=363800 Instructions Using the following options:...
thingiverse
very strong No bolt, no rust stick with PVC glue and use paracord to lace. ...(make a cone with scotch at the end of the rope to thread it easier)
pinshape
This is a paracord holder. ...This holder should hold at least 25' of paracord.
thingiverse
Just a little paracord winder I designed after years of dealing with knots. Will hold up to 100 feet of 550 paracord. ...I just use PLA at 20%.
thingiverse
I created this for Paracord Weavers that don't have the time to go out and buy an actual Paracord Fid.
thingiverse
Ein Anhänger für ein Paracord Survival Armband. ...Eine Kleine Dose und ein Fach für Notgeld.
thingiverse
A paracord spool I designed. ...To fasten the ends I did an overhand knot through one of the holes and wrapped. Designed for Paracord 550, but works for similar rope.
prusaprinters
A spool which holds about 75' of 5mm paracord. ...Could be scaled up or down to hold more or less cord. There is a hole in the center to thread the paracord through.
thingiverse
A paracord bracelet clasp designed to look like a drive chain link. ...15mm inside, but should scale OK.
thingiverse
This is a basic Paracord spool. Diameter 55mm. Only needs a 2 threads and threaded rod for complete. ...
thingiverse
He used pieces of card board to wind paracord. This removes the issues with cardboard folding and wearing out. A ladder for winding paracord. This is the second revision with additional internal support ...