particulate matter sensor 3d models
74240 3d models found related to particulate matter sensor.thingiverse
Indoor use particulate matter sensor on USB or Bluetooth. Since we live in big polluted cities the air quality is on a very poor level. But, the problem is not only connected to the big cities - even smaller cities and villages may suffer from air...
prusaprinters
Case for the DIY-particulate matter sensor from https://luftdaten.info/ Air enters through a tube on the side (8mm outer diameter) and leaves on the top through a grid. If you install it outside, mount it upside-down such that the temperature sensor...
thingiverse
A more comprehensive write-up about integrating the sensor in to a weather station is [here](https://karlquinsland.com/2020/08/adding-an-airborne-particulate-mater-sensor-to-ws3-weather-station/). The mesh filters are standard 19mm / .75 inch...
prusaprinters
I needed an enclosure for the the PMS5003 Particle sensor that would meet my needs: slanted roof so rain/moisture rolls off mesh covered inlets to prevent critters from making a home inside anchor points for screwing into a pole / wall Inspired by...
thingiverse
Microcontroller board NodeMCU v2 Sensors and Library DHT11: https://github.com/beegee-tokyo/DHTesp PlanTower PMS 5003: https://github.com/riverscn/pmsx003 SSD1306 128x64 0.96 inch OLED display module with I2C interface:...
thingiverse
This laser dust sensor can sense particulate starting from 0.3 µm and above, and is a reasonnable price/efficiency ratio so that you can determine if your air is heavilly polluted or not. Trust me, smell is not a good way to do that :) Measurement...
thingiverse
all credits to Chris for this great project: https://www.thingiverse.com/TheChrisP i just made a small modification so that the display reads all 3 particle sizes and thus removed the temp sensor hole from the model. For the Original instructions...
thingiverse
Components: 6x M3 - 4mm screw (Wemos Dual Base mount) 2x M3 - 10mm screw + nut (Particulate Matter Sensor holder) Plantower PMS7003 Particulate Matter Sensor 1x 10kΩ resistor 1x 10µF capacitor Wemos D1 Mini Wemos Dual Base Wemos SHT30 Shield Wemos...
thingiverse
stand_round_p3.stl is the side with nuts to put weather station (https://www.thingiverse.com/thing:3385510) and particulate matter sensor on the same holder. ...Solar cell power for the two sensors is published here :...
thingiverse
----------------------------------------------------------------- Particulate matter sensor. You need the top and the base. The SDS011 module is screwed with 2 screw 2.9x6.5 for example. The base part is screwed to the pipe (PVC DN40x3.0) with...
cults3d
The Co2 sensor alone or together with a particulate matter sensor. Common to all variants is a radar sensor to refresh the display to be performed only when present. You can also choose whether to use an Inky pHAT von Pimoroni or a Waveshare 2.13...
thingiverse
The scientific nomenclature of fine dust consists of fine particulate matter(PM). The world is blanked with particulate matter. PM from China is now becoming a big problem. Although the major components of yellow dust are sand and materials from...
thingiverse
Model of PMS3003 particulate matter sensor (dust sensor). ...Not for printing, rather for modelling your projects.
grabcad
SDS021 particulate matter sensor, contains small 20mm fan and sheet metal shield. ...Dimensions are rough as parts are not so precise.Fan from benjamin: Fan 20 x 20 mmConnector from TE: http://www.te.com/usa-en/product-1734598-5.htmlManufacturer site:...
thingiverse
Base plate to hold an ESP8266 and SDS011 particulate matter sensor. Here's how to build your own sensor & contribute data to the community: https://sensor.community/en/sensors/airrohr/ The official instructions say you can house the sensor in a...
prusaprinters
I purchased the PM10 & PM2.5 sensor sds011. As many have done I added the temperature and humidity sensor. everything managed by an Arduino esp32 and Matt, sending data to my DB influx and graphing everything with Grafana. ...Of course with node-red...
thingiverse
there are many cases on thingiverse, but most of them put the sensor in a position which is not suggested by the producer (I have also added some pictures from the producer). So I decided to make one mine., very simple, but that can be used in 2...
thingiverse
This is a case for an air quality sensor that uses a Plantower PMS5003 sensor to measure airborne particulate matter. The sensor is controlled by a TTGO T-Display ESP32 microcontroller / LCD display. ... The project is designed for middle school...
thingiverse
This is a case for the Raspberry Pi Zero with the Pimoroni Enviro+ Air Quality board and a Particulate Matter Sensor. ... SCAD file for version without the Particulate Matter Sensor coming soon.
thingiverse
Then created pilot holes to connect cable runs and a case for the supported particulate matter sensor (PMS5003). Included an (untested) mount for the Raspberry Pi Camera Stand by @atleberg ( https://www.thingiverse.com/thing:274111 ). This is...
prusaprinters
Housing for popular particulate sensor SDS011. For mounting you need 5 M3 brass inserts. There is enough room for included USB converter. ...On the sides are openings for intake air and exhaust with slide in options for mesh to prevent insects...
thingiverse
---- This is a frame for a [luftdaten.info](http://luftdaten.info) compatible particulates sensor. The original sensor is housed in drain pipes, which is cheap, but also looks quite like that. ;-) This construction uses an OBO Bettermann T60...
thingiverse
This is a stand for a Raspberry Pi Zero, Pimoroni EnviroPlus Hat and the optional PMS5003 Particulate sensor: https://shop.pimoroni.com/products/enviro-plus https://shop.pimoroni.com/products/pms5003-particulate-matter-sensor-with-cable
thingiverse
- The particule matter sensor (https://www.thingiverse.com/thing:4147660). - The main unit based on ESP32 board with wifi and its solar power supply (coming soon). - The rain gauge sensor. I will add after a wind speed meter. ...
thingiverse
What is Matter connectivity? ... Matter is a universal connectivity standard to make the use of smart home devices and IoTs simpler
sketchfab
Grey Matter 3d Model | created by Jeetesh Singh | Grey matter is an alien from Ben 10 series | Not Rigged | Materials Included |