pegs and jokers game 3d models

have recently become fascinated with the game "Pegs and Jokers", but not necessarily fascinated with the prices. So after seeing the simplicity of the game design, I decided to design and 3D print a less expensive version. The design only requires...

have recently become fascinated with the game "Pegs and Jokers", but not necessarily fascinated with the prices. So after seeing the simplicity of the game design, I decided to design and 3D print a less expensive version. The design only requires...

This is Pegs and Jokers board game that can accommodate 3-8 players, depending on how many pieces you print. Print as many game board pieces as there are players, then connect them in a circle. Print 5 pegs for each player. I had to use wooden...

Pegs and Jokers gameboard as prescribed at https://www.pagat.com/race/pegsandjokers.html Print as many of these as there are players, they hook together in a circle.

Customized version of https://www.thingiverse.com/thing:1842869 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1842869

3D printed pegs to go along with the boards located here: https://www.thingiverse.com/thing:1988720 I didn't want to fuss with going to get wood dowels and cut them down to use the peg toppers provided in the original post. Printed with PLA or...

Customized version of https://www.thingiverse.com/thing:2873982 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2873982

There is not a "standard Pegs & jokers" and this version and ruleset we call the California rules (Rules are included in pdf file). This set uses standard ~1/8 inch (~3.2mm) cribbage pegs that can be found on ebay and other sites. I show a...

There is not a "standard Pegs & jokers" and this version and ruleset we call the California rules (Rules are included in pdf file). This set uses standard ~1/8 inch (~3.2mm) cribbage pegs that can be found on ebay and other sites. I show a...

I his is a case for my "travel Pegs & Jokers" https://www.thingiverse.com/thing:3061408 I print it both with brim as well as supports. I left enough room for storage of the pegs. I CA glued the slip-fit sections together. ...

A game for those who don't play with a full deck! Using a limited number of cards (some with special abilities) each player tried to back the other into a position where they cannot move. Only problem is the other guy can move the same pieces you...

The board and pegs are easy to print and gives you everything you need except 4 dice. You need to print 3 pegs of one color, then 11 to 12 pegs of each color per player. The game is for up to 4 players but I usually play it with my wife. If you only...

A take on Pegs and Jokers but using marbles. This board was designed to hold a basic 16mm marble and supports down to 3 player board configurations, and up to as many as you need. If anybody doesn't like the missing wedge in the corner when playing...

-- Update 1: 12/21/2021 I printed this fully and found that because I smoothed out the threads since my original test print that the lid turned an extra 38 degrees before tightening up against the base so I made a new lid to correct for that...

I suggest to make the pegs a different color than the board. This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/kWNqsLgDfqB

Customized version of https://www.thingiverse.com/thing:3061408 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3061408

Customized version of https://www.thingiverse.com/thing:3061408 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3061408

Customized version of https://www.thingiverse.com/thing:3061408 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3061408

Missing the pegs for your Attack Wing games? Print these replacement pegs. If your printer pauses after short segments and 'oozes' filament then print them in sets of five pieces. I've found that gives the printer enough time let the first item...

We've lost a bunch of the pegs for the mastermind game. These are the smaller pieces that fit into the version of the game we have. ...

Instructions Holes/pegs are 10mm, 8mm, 6mm, and 4mm diameters. Overall it is 45mm by 25 mm. The extra squareish area near the large peg is 15mm by 15mm. The holes are 5mm deep, and the pegs are 5mm high. I tried to make the dimensions as pleasant as...

Pegs are 2mm, 3mm, 4mm and 5mm. ...Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter ...

Peg to mount the spool holder on its arms if you don't have real bearings and the leadscrew. The central screw without the base to center your spool on the mount. Longer filament sensor holder for the sidewinder X1, aligning it to the extruder. ...

My kids got a copy of the game Otrio, which came with doubles of one color none of the 4th color that was necessary for a 4 player game. So, I modeled these so that a 4th person could play. ...This also allowed people to pick the colors for their own...

... during this COVID-19 pandemic. ...But, they can be used for anything you need to hang up while driving. There are six versions: In size, long, short, and micro. In style, pegs and hooks. I print on its side and with supports between the pegs/hooks.

... during this COVID-19 pandemic. ...But, they can be used for anything you need to hang up while driving. There are six versions: In size, long, short, and micro. In style, pegs and hooks. I print on its side and with supports between the pegs/hooks.

Now the tortoise and hare can compete in a friendly cribbage game !

This is our version of the popular Triangle Peg puzzle game, sometimes referred to as Tricky Triangle. Rather than leaving the pegs in the holes on the board, we added a dovetail-lidded box to hold all the pegs. ...The dovetail lid has a small latch...

Same peg as the original. ...Print with the hole facing up.