ph probe holder 3d models

I use a pH probe for stability testing, unfortunately the manufacturer doesn't sell any holders for it and as it isn't held upright the storage solution can run dry, causing the probe to become damaged. ...I designed this to overcome this issue.

Simple 3d printed probe holder for reef tank. ...Holes are sized for 1/2'' diameter probes and the magnet slot is sized for a plastic coated magnet 1" x 1/2" x 1/4" thick.

Replacement for the Suction Cup Holder (which regularly lets the Probe drops into the water). ...Fits all Diameters of 13-14 mm and Glases of 12mm thickness or less.

Simple Holder for a PH Probe (unknown chinese Brand, 13mm diameter). ... Will fit to the edge of the Bioflow filter (tested on Rio with Bioflow M, also fits on Bioflow S) to hold the PH Probe just above water level.

... grip. ;D Also print it with higher numbers of outside perimeters, to get 100% infill/stronger print. Outside probe diameter: 19.30mm Peg diameter for silicone sucker: 4.5-5.5mm Suckers: http://alishort.com/5Jw5c Probe: http://alishort.com/YoV7C

Hi. ...This is my first project. This is holder for Weipro Ph meter probe. ...(tank with rims) Created in https://www.tinkercad.com

This is a 2 probe holder, It works with a 11mm pH probe and a 12mm EC probe. Both bought in DFRobot webstore. ...Print Settings Printer Brand: RepRap ...

Aquarium holder for Hydromet PH probe. ...Suitable for glass thickness of 8 mm

This is a holder for an Atlas Scientific pH Probe ( or other appropriately sized probes) and a Waterproof DS18B20 Temperature sensor, which suctions to the side of an aquarium. Having these two sensors together allows for temperature compensated pH...

I printed it in ABS & added manual support under the GoPro mount. ...Otherwise it prints without problems at all.

A pH probe holder designed for the KH Keeper Plus from Reef Factory. It is meant to replace the standard O-rings and align the pH probe perfectly above the magnetic stirer fish. ...It slides on the standard probe mount.

The PH probe and his controller, these are the good measures taken from the SEN0169 that you can recover on the web.

Atlas Scientific pH-probe

This pH probe will fit 100s of models/brands of Aquarium Computers, Aquarium Controllers, pH Monitors and pH Controllers; both dual and standalone types.

Made this thing to wash the the Ph probe in a water treatment plant with air or water. ... Please feel free If you like this model and you want to support my work that I am making, you can donate me if you want with paypal: http://paypal.me/SeanManagh ...

At work I needed something to hold a pH probe off the bottom of the container while calibrating and came up with this. It fits a Rosemount 396P perfectly (1" MNPT) but may work for others. Co-workers requesting I print more... Not sure how to...

... findet in der hinteren runden Aussparrung des Deckels platz . ...Meine Ph-Sonde ist in diesem fall von JBL. This is a pH probe holder for my Juwel Aquarium, which fits in the round rear recess of the lid. ...In this case, my pH probe is from JBL.

Fake 12mm Probe to insert in your poolsystem in winter or while you take the real probe out for calibrating or replacing. It avoids air sucked into the system or water spilling out. ...

Shrouding to guard the pH probe against bumps and drops with mount for easy fitting. ...Protecting this rather fragile device.

ph holder for 30mm ph meters ang on for aquarium

Remix of an existing design by gotfrogs. ... Used Tinkercad to cut away a section at the front to allow connection of the PH Probe and access to the calibration screws. ...

It's the same size as a credit card or your business card. ... It is adjustable. Take it comfortably in your shirt pocket. It is the new Phone Holder "PH-Card".

... Printed with MakerBot Replicator 2. The pH electrode holder is made a little bit thicker to be stronger and more durable due to its continuous contact with water. It works perfectly, Enjoy! ...   Original article on this project can be found here.

This is a device to facilitate the pH measurement when using large bottles. ...Many times the arms that come with the pH measuring equipment are not large enough to be used with bottles of one liter or more.

Should fit most pH pens. Always best to store it vertically. I put a little storage solution (KCl) in the cap to keep the bulb sensor happy. Can be scaled to fit your pen easily. I used Tinkercad. ...

code: https://github.com/frossty/Ph_Temp_Prob Tools: PH probe with BNC converter: https://www.aliexpress.com/item/32957428276.html?spm=a2g0s.9042311.0.0.142a4c4dEZFU4D ESP8266:...

A secure holder for your pH solutions when calibrating. ...No more spills!

Holder for probes so that they do not lie around

A holder for your probe for your cnc machine, better as in a box.