picatinny riser 3d models
9083 3d models found related to picatinny riser.grabcad
A (almost) fully adjustable picatinny riser and rail. Control through custom properties. It allows heights from roughly 19.5mm to 50mm. 7 tooth minimum, unlimited top end. ...It also has properties that add extensions on the ends, but still allows for...
thingiverse
This is a small picatinny riser which I wanted to see if I could re-create by hand. ...It was used in this blog post: https://blog.robseder.com/2015/04/18/3d-printing-mega-post-how-to-get-decent-prints-april-2015-edition/ Print Settings Printer Brand: ...
thingiverse
Picatinny riser designed for the Caliburn platform. Contains small sights built in. May work as a carry handle, but was not tested extensively nor designed for the purpose. Uses 6-32 x 1-1/4" countersink screw and hex nut, but can usually friction...
thingiverse
19mm Riser for Optics on an Airsoft Gun. Used this on a VFC MP7 GBB. ...Print it in vertical direction for maximum bending stiffnes.
thingiverse
Could not find a picatinny riser that suited my needs. Designed this one to try and blend in with the upper receiver. Users two M5 screws and nuts. ... Printing: The supports around the screw holes can be tricky to remove, so block supports via...
thingiverse
Hello, Here's another picatinny riser for small or big optics (if your want to print it twice). I printed mine in ABS for stronger material and i'm happy with it. Use a 5mm hex head screw and nut for mounting it on your favorites replica's. ...(I...
thingiverse
25mm Picatinny Riser hardware needed: 5mm x 30mm bolt, with a head no larger than 9mm nut with 8mm wrench flats Slots are sharkfinned to simplify perimeter topology for fewer retractions and improved print quality. Should still be compatible with...
thingiverse
A picatinny riser that can go on worker rails. If you like your optic or you flashlight a bit higher. Works with worker rails, though depending on the quality of your print, you might need to sand the inside of the rail a little. I don't...
thingiverse
This is a simple picatinny rail riser I use to lift my sight off of my Game Face Trion. This rail increases high by about 3/4". The rail secures to an existing picatinny rail using 2 M5 x 30 Socket Head Cap Screw. ...Amazon Link:...
prusaprinters
25mm Picatinny Riser hardware needed: 5mm x 30mm bolt, with a head no larger than 9mm nut with 8mm wrench flats Slots are sharkfinned to simplify perimeter topology for fewer retractions and improved print quality. Should still be compatible with...
thingiverse
An angled picatinny riser intended for mounting optics. Mainly intended for Nerf applications where the dart will drop a significant amount at most engagement ranges (I developed it after noticing one of my blasters would consistently shoot under a...
thingiverse
5 slot picatinny riser that can be used to raise any compatible device 0.6 inches. Requires the following hardware: 1: [1 inch #8-32 button head screw](http://amzn.to/2BnJ3tC) or similar 1: [McMaster-Carr...
thingiverse
This is a Picatinny rail riser I designed for use with the Matrix RD210 red dot. ...It uses an M3 bolt that is ~22mm long.
thingiverse
Grüße ---------------------------------------------------------------------------------------------------------- Hy This is my attempt at a Picatinny riser, I printed the risers horizontally, requiring a minimum of support structure and creating...
thingiverse
... for gas block height sights. ...The BCA ones are super cheap but none of my ARs have gas block rails so I mounted the rear iron on this riser to line them up. ... Single screw version and bridge version if you feel extra strength is needed.
thingiverse
Original design was too tight so i losen fitting and shorten picatinny rail I suggest using support blocker and modify mesh setting for 100% infil on bottom, and 50% infil on top. ... Supports set on "touching build plate"
thingiverse
The old version couldn't fit on a standard picatinny rail, so I made it so it could. ...Also added one with a cutout for a bolt and nut.
cults3d
Hello, I present two models of riser rail for airsoft and asg replicas. The taller one is 31.50 mm high and the other is 21.50 mm high. ...To connect them I used 4 M8 screws, 35 mm long, and 4 nuts.
thingiverse
... 4 walls. Attaches using the same screws you would have after removing the original top mount (M4 x 10mm) Supports optional depending on how well your printer manages bridges and overhangs. They are only need to support the picatinny section.
thingiverse
picatinny riser with 20mm lift. has 3 rails on front section angled at 45*. ...only one of front rails should be used at once!
thingiverse
Two part picatinny riser (length 155mm, raises viewpoint 20mm). You need two M5*30mm screws and two M5 nuts. I recommend to print in the default orientation because removing the supports can be a bit of a hassle. ...
thingiverse
Features Works on standard 21mm Picatinny/RIS rail Uses metric nuts and bolts Wisdom tooth not included Instructions Print it in PETG for a stronger part Uses M3 nut and M3x30mm (or longer) bolt Use supports and print it with the front or backside on...
thingiverse
I needed a riser to fit the RMR onto my AR15 and this is what I came up with. 3 slots on a single rail section for RMR, Bushnell trs25, and any other optics or accessories that are too low on their mount. I've uploaded 3 STLsFirst is a whole body...
cults3d
I needed a riser to fit the RMR onto my AR15 and this is what I came up with. 3 slots on a single rail section for RMR, Bushnell trs25, and any other optics or accessories that are too low on their mount. I've uploaded 3 STLs First is a whole body...
thingiverse
Picatinny rail riser - 13 mm. ...Suitable for airsoft or paintball.
thingiverse
airsoft picatinny rail riser, fixed stl version ofhttp://www.thingiverse.com/thing:188867 print with supports!