pipette bottle 3d models
45290 3d models found related to pipette bottle.
cults3d
Four plans (stl): - 1ml pipette to 100-150ml bottle (diamater 45-60mm) - 1ml pipette to 200-250ml bottle (diamater 60-65mm) - 3 or 5ml pipette to 100-150ml bottle (diamater 45-60mm) - 3 or 5ml pipette to 200-250ml bottle (diamater 60-65mm) Pipette...
thingiverse
This will attach your pipette to your 500 mL bottle of whatever from Seachem. I use Prime and Flourish excel but I'm guessing it will fit most of their bottles. ... I use these pipettes...
grabcad
Dropper bottle with glass pipette, content liquid and label. ...All models without textures and materials.
thingiverse
This handly little holder helps by keeping the pipette with the bottle of solvent or whatever. PRINT USING PLA!!! The solvent (plastic cement, thinner, etc) will melt ABS but won't melt PLA. The ring is a oversized slightly to fit over the label on...
cults3d
Designed a pipette holder that attaches to the General Hydroponics Up & Down 1 Quart (946 ml) container. ...It does fit other 1qt containers like the Instant DeChlor as soon in the picture.
thingiverse
Designed a pipette holder that attaches to the General Hydroponics Up & Down 1 Quart (946 ml) container. ...It does fit other 1qt containers like the Instant DeChlor as soon in the picture.
grabcad
Check out our write-up in BioRxiv: http://biorxiv.org/content/early/2017/02/20/109231
thingiverse
Pipette dispenser for 155mm, 3ml plastic pipettes used for airbrush color mixing or for laboratory applications. ...Holds around 100 pipettes.
prusaprinters
You can attach this print with a simple cable tie to your chemical and you can always be sure that the pipette is matched with the chemical in the bottle. If the print slides to much you can try to use Ninjaflex as the base for the first layers. I...
thingiverse
Customized pipette holder for our shelves, stays on friction alone but adhesive suggested.
thingiverse
<b>Another quite simple laboratory equipment, made on request of my wife, to replace the old and broken one from the store. ... The angle of the pipette from the vertical is ca 15-25 degrees, depends on pipette model.
thingiverse
A simple pipette stand for 4 single channel pipettes (without tips). Made with FreeCAD. ... Instructions Makerbot Replicator 2x Settings: Infill: 10% Number of Shells: 2 Layer Height: 0,3mm
thingiverse
You always wanted that cool Pipette-pen that everyone is talking about? Well this is your chance to 3D print one! ... It will fit a common BIC pen insert.
thingiverse
Hook for hanging DragonLab TopPette brand pipettes- may need some scaling for different brands. ...Just print and attach some double-sided tape on the smaller side to mount on your surface of choice- done!
thingiverse
A spipette stand for multi and single channel pipettes (without tips). Made with FreeCAD. ... Instructions Makerbot Replicator 2x Settings: Infill: 10% Number of Shells: 2 Layer Height: 0,3mm
thingiverse
Needed something to keep the pipette with the jug for the peppermint oil (the jugs don't come with a dropper top), also needed something to cut down drip messes while I'm mixing the wife's e-juice. ...So, I worked this up to clip onto the small jug...
thingiverse
... colour options. I recommend transparent green, it looks great in the lab. Cost of a spool of filament is roughly the price of the least expensive pipette stand out there (that I've found), and you can print multiple copies, over various sizes.
thingiverse
I made this for my long airbrush pipettes. I glued the racks to the top piece but left the bottom part loose so I could wash it out when I needed to. ... The uprights were done st 100% as they are fairly thin.