playmat tube holder 3d models
409144 3d models found related to playmat tube holder.thingiverse
Holder for the Ultra Pro playmat tube (https://www.ultrapro.com/product_info.php?products_id=2298) to keep it from rolling off the table while playing.
prusaprinters
Holder for the Ultra Pro playmat tube (https://www.ultrapro.com/product_info.php?products_id=2298) to keep it from rolling off the table while playing. Category: Hobby
thingiverse
I have also added in files for a 2-piece tube print so those with smaller printers can also print playmat tubes! Approximately 190mm for each section. ... Full disclaimer: I have not yet printed one of the 2-piece tubes myself, it looks like for the...
prusaprinters
This is a basic holder that slides onto the end of the playmat [ you will need two, one for each end] to protect the playmat and its edges when not in use. The gap for the playmat to ‘slot’ into is 9mm, this will fit all standard Pokémon...
thingiverse
I had tried some of the playmat holders out there and decided to try my had at my own.
thingiverse
This Little cup is made to close a tube for Card game playmat! For now I'm uploading only one cup, you can print it and close your playmat with! ...Then I'll upload a more complex version with instruction and photo!
thingiverse
Updated February 8th, 2023: Added part Playmat_Tube_Spiral_Top_Short, its 30mm shorter. These parts are interchangeable with my other play-mat tube designs Spots and Stripes. https://www.thingiverse.com/thing:5616827 ...
thingiverse
Remixed to hold a rolled-up MTG playmat, and to print without supports. I also sliced a cylinder out of the center, to make a smoother inner-surface to slide the mat into. It is very tall, and I had to use my Tevo Tornado to print it. You could...
cults3d
Remixed to hold a rolled-up MTG playmat, and to print without supports. I also sliced a cylinder out of the center, to make a smoother inner-surface to slide the mat into. It is very tall, and I had to use my Tevo Tornado to print it. You could...
thingiverse
... These parts are interchangeable with my other play-mat tube designs Stripes and Spiral https://www.thingiverse.com/thing:5616859 https://www.thingiverse.com/thing:5616839 Note: This model was designed to be printed using a .4mm diameter nozzle.
thingiverse
Either version can be made longer adding an extra Centers section, each one will extend the tube by 12.5cm (4.9 inches). These parts are interchangeable with my other play-mat tube designs Spots and Spiral. https://www.thingiverse.com/thing:5616827...
cults3d
... The "Remix" function did not work to link the source files properly....potate-verse at it's finest. ... I split the tube into to pieces to be able to print it on my Ender 3 V2. ...I also added a "reinforcement" ring to enlarge the glued surface area.
thingiverse
... function did not work to link the source files properly....potate-verse at it's finest. ... I split the tube into to pieces to be able to print it on my Ender 3 V2. I also added a "reinforcement" ring to enlarge the glued surface area. ...
prusaprinters
This is a remix of: https://www.thingiverse.com/thing:3544399 and: https://www.thingiverse.com/thing:517581 The "Remix" function did not work to link the source files properly....potate-verse at it's finest. I split the tube into to pieces to be able...
thingiverse
njeff's playmat tube was not only too tall for my printer, but was too wide for some of my thinner playmats. I shrunk it to fit thinner playmats, and only 10cm tall. ...Works like a charm.
prusaprinters
Either version can be made longer adding an extra Centers section, each one will extend the tube by 12.5cm (4.9 inches).These parts are interchangeable with my other play-mat tube designs Spots and SpiralNote:This model was designed to be printed...
prusaprinters
Either version can be made longer adding an extra Centers section, each one will extend the tube by 12.5cm (4.9 inches).These parts are interchangeable with my other play-mat tube designs Spots and StripesNote:This model was designed to be printed...
prusaprinters
Either version can be made longer adding an extra Centers section, each one will extend the tube by 12.5cm (4.9 inches).These parts are interchangeable with my other play-mat tube designs Stripes and SpiralNote:This model was designed to be printed...
prusaprinters
You will probably need to print 2 of these, but you may as well try using a single one, and balancing your playmat tube with the help of a wall.Use some common wooden screws to attach it. Will need 2 of those per print.</p><p>The one in the picture...
thingiverse
A mountable playmat holder that you can screw up on your wall or shelf to store your playmats. Great for collectable card games like Magic the Gathering or Android Netrunner. I've included 3 versions. Playmat Holder - A completely circular one. ...
prusaprinters
Great for collectable card games like Magic the Gathering or Android Netrunner.I've included 3 versions.Playmat Holder - A completely circular one. Consider it a bottom piece, and an optional top piece.Playmat Holder Cut - One where one of the edges...
prusaprinters
Holder for a playmat that has under 10cm diametr when rolled up. Does not requier any mounting, gluing, drilling or any other type of fixin. Just slides on kallx from behind and gets fixed in by pressing against wall. ...Does need supports but can be...
thingiverse
This is the same diameter as Ultra Pro tubes, but the caps can be used for any 2" diameter tube -- I used these 16.5" long polycarbonate tubes: https://www.amazon.com/dp/B093GS1T7R?ref=ppx_yo2ov_dt_b_product_details&th=1 I made these so my playmat...
thingiverse
Brackets to hold a Monster double playmat holder to a Stanley tool box for gaming travel case. Card Game - Magic the Gathering. ... Hardware: 2 - 5mm 4" threaded rods 4 - 5mm acorn caps 4 - black nylon spacers/washers
thingiverse
a simple playmat holder no support is needed total length is 38cm inner diameter is 4.9 cm
cults3d
Dicemaster Playmat, Quite big, scale as needed. ... Might do a modification to make it foldable, but that would be a future project.
thingiverse
Dicemaster Playmat, Quite big, scale as needed. Might do a modification to make it foldable, but that would be a future project. ...