playseat challenge gearshift mount 3d models

Use this universal mount to proper secure things to a playseat challenge, or other things with 25mm tube diameter.I used it to mount the power-supply. ... Hardware needed: 2x M4x30 Screw 2x Washer for M4 2x M4 nut

A set of mounts designed to rigidly mount the Fanatec Clubsport V3 pedals to the Playseat Challenge. May also fit other pedal sets. ... More Information:...

Clear the wheel mount tubing latch The outside mount and surface are in 2 pieces for a couple reasons: 1. Can hopefully be printed on printers with a smaller build volume. If it were a one-piece assembly, it would not fit on the print bed of my Qidi...

I wanted a robust shifter mount for the Playseat Challenge, and used the https://www.thingiverse.com/thing:2914511 as basis, creating a non adjustable and sturdy mount. Use three 6mm bolts to mount it to the Playseat. ...

I wanted a robust shifter mount for the Playseat Challenge, and used the https://www.thingiverse.com/thing:2914511 as basis, creating a non adjustable and sturdy mount. ...Use three 6mm bolts to mount it to the Playseat.

Here's a mount I designed that allows you to install a 25mm bar onto the leg frames (front or back) of a Playseat Challenge. I used this to attach my own Bass Shaker to my Playseat Challenge. ... Here's a 3 part video on how I did that showing the...

A shifter mount for mounting Logitech shifters onto the Playseat Challenge racing rig. Logitech-playseat01 is the shifter mount for mounting on the right side Logitech-playseat02 is the clamp for mounting on the right side and Logitech-playseat03 is...

Mount for mounting body shakers (Bass Pump III) to the Playseat Challenge&nbsp;You need more simracing parts? Hace a look: <a...

Just trying to design a mount strong and eazy to print and mount as possible.main part is redesign from "Playseat Challenge Shifter Mount" by jeoje" Drawback: The plastic pad latch(which you open every time you leave the seat),only can open from...

The design goal of this mount was to hold both parts of a hotas setup in place without sacrificing any folding and storage capabilities of the playseat challenge. Depending of the thickness of the rubber there are two versions to print. One for...

Universal mount for button box. Add a hole on the box side. You might want to use glue for the box & a rotary to keep the placement. ... - 5x M3 - 5x M3 Nut

... inside the clamp, where it makes contact with the chair tube. After the support is mounted on the chair I used two leftover screws from my playseat challenge and mounted the gear shifter. ... If anyone needs the source files I can share those too.

Mounting bracket for PlaySeat Challenge. Made it for mounting Fanatec shifter. The white plate on picture is for mounting Heusinkveld Sequentil shifter. They can be used for mounting all other plates and accessories. Mounting hole is 6mm, you need...

It is around £30 for an extra mount for a gear shifter on the playseat challenge so I set out to make my own mount that is better suited for where I want it positioned. It's extremely strong when printed with carbon fibre filament and you can...

This universal mount is designed for the Playseat Challenge. The mount was originally designed for the shifter plate from Advanced Sim Racing. But it can be used for any custom design. The spacing between the mounting holes is 85.2mm. Hardwares: ...

A shifter mount for mounting the Thrustmaster TH8 onto the Playseat Challenge racing rig. This is extremely sturdy and will not budge. TH8-playseat01 is for mounting on the right side TH8-playseat01-nuts has holes for inserting M4 nuts...

I needed something to mount Fanatec V3s pedals on Playseat Challenge, so I came up with this design. I've printed this in PLA, but you could go with PETG for strength There are 2 variants, one for M8 bolt since v3's has 8,5mm holes for mounting and...

Mount for fixing an Anker USB hub to your Playseat Challenge.Flex the mount slightly and slide the USB hub into it. Fix it with two zip-ties. Done!</p><p>&nbsp;</p><p>You need more simracing parts? ...Hace a look: <a...

The handbrake will sit 25 degrees tilted forward when mounted to a playseat challenge and clears my 300mm WRC wheel on my fanatec CSL DD. Most TM/Logitech wheels are 280mm so you'll have even more room. There is a small pedestal for an arduino board...

This is my mount for a Logitech driving force shifter on a Playseat Challenge. It mounts everything far away from the opening mechanism (mounted on the right side of the seat). Should work for our right-hand drive friends as well if you mirror it in...

I needed something to mount Fanatec V3s pedals on Playseat Challenge, so I came up with this design. I've printed this in PLA, but you could go with PETG for strength There are 2 variants, one for M8 bolt since v3's has 8,5mm holes for mounting and...

This model utilizes the remaining hex cap bolts from my Playseat Challenge which makes it a "no hardware" design with the assumption that you kept spare hardware post installation. There are a total of six printed parts. Four latch on to the frame...

* Install ZipTies in mounts * Tighten ZipTies around Playseat Challenge by pulling down then pulling up * Trim ZipTies Requirements: ============ * 1x 5mm Allen Key * 1x 10mm Wrench * 8x ZipTies 5mm * 2x M6x16mm Socket Head Bolt (low profile, so it...

Hey all, this is my remix of a popular shifter mount that allows us Playseat users to use the OSS (open sim shifter) on our rigs! Simply use longer bolts and this attaches the same way the faceplate does. ... See the original make for the other half of...

This is an extremely sturdy and flex-free SHH Shifter and/or Handbrake mount for the Playseat Challenge, based on the TH8A mount from floano. SHH Shifter with TH8A Mount: https://www.shiftershh.com/en/extra-mounts/21-152-soporte-extra-th8.html...

I really liked jeoje's design for the Playseat Challenge, but I didn't have any M3 hardware that was long enough. I had some M6x40mm flat head screws leftover from another project, so I decided to use those instead. I started from scratch using...

I really liked jeoje's design for the Playseat Challenge, but I didn't have any M3 hardware that was long enough. I had some M6x40mm flat head screws leftover from another project, so I decided to use those instead.</p> <p>I started from scratch...

This is a pretty crude remix of the awesome playseat shifter mount by jeoje. I combined the outside bracket and the shifter mount plate into one piece. I reduced the thickness of the mounting plate and added holes for the TH8a bolt pattern. I also...

I was looking for a way to mount my speakers to my play seat challenge so I made this mount. 20% infill. I used both PLA and PETG because its what I had on the printer. Hope this is useful to someone else. In order to use this you have to...

The remix of fr3zno is very decent! ... The corners of the mount were a bit sharp so I made a small modification by smoothing the corners. ...