pokemon card holder 3d models

376404 3d models found related to pokemon card holder.
pokemon card holder v2
pokemon card holder v2
thingiverse

pokemon card holder version 2

Pokemon Card Holder
Pokemon Card Holder
thingiverse

Easily Customizable and easily printable Pokemon card holder for one deck and one card to be put on display

Pokemon card holder
Pokemon card holder
thingiverse

You also got into the pokemon hype ? ... You should try this pokemon card holder to show off your best card ! :pikachu: There is 2 version available one with sleeve protection and one without! ... infill :10% No support needed

Pokemon Card Holder
Pokemon Card Holder
thingiverse

Pokemon Card holder, each holder can hold up to 4 cards. ... Opening Aperture: 63.5mm (Slanted towards display face) x 1.5mm Print face up, no support or brim needed.

Graded Pokemon Card Holder - PSA
Graded Pokemon Card Holder - PSA
thingiverse

This is made specifically for the PAS graded pokemon card holder. ...I uploaded the CGC too.

Graded Pokemon Card Holder - CGC
Graded Pokemon Card Holder - CGC
thingiverse

This is made specifically for the CGC graded pokemon card holder. ...I uploaded the PSA too.

Pokeball Pokemon Card Holder (printable)
Pokeball Pokemon Card Holder (printable)
thingiverse

I made the "Poke- Ball Pokemon Card Holder by usnavy7" printable and added a black stripe I split the Ball into three .3mf-Files, to print with each color seperate. ... You will need some Glue and a Spring.

Pokemon Card Holder
Pokemon Card Holder
thingiverse

Basic Pokemon (or other) card holder. Sized to fit cards in sleves. These were sized to fit a full 60 card deck with Titan sleeves on them, the images are from a full deck in sleeves. ...

Pokemon Card holder
Pokemon Card holder
cults3d

Small Pokemon TCG holder, will fit other TCG Cards with the same dimension's Simple design with top loader style and small grooves for the card to sit secure in the stand

Pokemon Card Holder
Pokemon Card Holder
thingiverse

hold all of ur trading cards (i made this for pokemon cards)

Pokemon Card Holder
Pokemon Card Holder
thingiverse

This is a clip to help keep pokemon cards together while playing. It allows you to keep energies stored to the right and condition cards to the left. ... There is an optional dmage counter holder that can be glued on top.

Pokemon Card Holder
Pokemon Card Holder
thingiverse

Made this cause I needed somewhere to store my Pokemon Cards. ...Fits a decent amount.

Pokemon Card Holder
Pokemon Card Holder
cults3d

This will hold a Pokemon card with the hard case protecting the card and make it look good while on display.

Pokemon card holder
Pokemon card holder
thingiverse

Poke'mon upright card holder display.

Pokemon Card Holder/Display
Pokemon Card Holder/Display
thingiverse

Card holder to display cards. ...Sized to fit cards in ultra pro 5x3 semi rigid protectors.

Pokemon Card holder
Pokemon Card holder
thingiverse

DIY Pokemon game card storage ball,remember need install 4 magnet(diameter=9mm, thickness=2mm) for push button and cover lift used. ...If some mismatch while parts installation, please let me know and i will modify parts stl file for you, thanks.

Pokemon Card Holder
Pokemon Card Holder
thingiverse

http://www.thingiverse.com/apps/customizer/run?thing_id=434793 Instructions Using the following options: both_gap = 10 card_gap = 10 support_gap = 0.25 clip_card_gap = 0.25 angle = 8 holder_height = 64 card_width = 64 holder_count = 14 bar_thickness...

Pokemon Card Holder
Pokemon Card Holder
thingiverse

http://www.thingiverse.com/apps/customizer/run?thing_id=434793 Instructions Using the following options: card_length = 88 overhang = 16 support_gap = 0.25 card_width = 64 top_offset = 14 both_gap = 10 angle = 18 holder_count = 14 card_gap = 5...

Ultraball Pokemon Card Holder
Ultraball Pokemon Card Holder
thingiverse

Ultraball made to hold pokemon cards. Uses (10) 5mm dia x 2mm tall magnets to hold the lid on. The top sections are interchangeable with the pokeball I made but not the original that I created this from as I moved the magnets slightly. Changes from...

Pokemon Card Holder
Pokemon Card Holder
thingiverse

(I even have 64 in mine and there isn't an issue.) So improvements are: Hold 60 cards for a full Pokemon Deck Now has a deeper and wider cavity at the base for damage counters. I have also enlarged the hole on the lid to accommodate the new larger...

Jumbo Pokemon Card Holder
Jumbo Pokemon Card Holder
thingiverse

I printed it flat without supports on my Ender 5 and due to the overhangs inside the card holder it strings a little bit. I used a utility knife razor blade to scrape out the slots that the card slides in to clean out any filament debris. This...

Pokemon Card Holder
Pokemon Card Holder
prusaprinters

(I even have 64 in mine and there isn't an issue.) So improvements are: Hold 60 cards for a full Pokemon Deck Now has a deeper and wider cavity at the base for damage counters. I have also enlarged the hole on the lid to accommodate the new larger...

Pokemon card holder
Pokemon card holder
thingiverse

This Pokémon card stand is very easy to print. ...

pokemon card holder
pokemon card holder
myminifactory

i made them for my granson to keep his poke cards safe. ... they're durable and stackable

Pokemon Card Holder
Pokemon Card Holder
cults3d

This was designed for a friend who likes to keep his cards organized. It is fit for not just the plain card but also for a sleeve that he had. ... If you would like to see my other designs go here: ...

Pokemon Card Holder
Pokemon Card Holder
thingiverse

This was designed for a friend who likes to keep his cards organized. It is fit for not just the plain card but also for a sleeve that he had. ... If you would like to see my other designs go here: ...

Pokemon Card Holder
Pokemon Card Holder
prusaprinters

This was designed for a friend who likes to keep his cards organized. ...It is fit for not just the plain card but also for a sleeve that he had.   

Pokemon card holder
Pokemon card holder
cults3d

The cards don't move anymore and there is no risk to damage the edge or the corners Possibility to print up to 8 dividers and find easily the cards of a series (print 4 times the N°1 and 2 and return them) The print is a little overflowing on the top...

pokemon card holder
pokemon card holder
thingiverse

A simple holder for a standard size Pokémon crate. ... Made with a WANHAO duplicator 12.

Pokemon Rare Card Holder
Pokemon Rare Card Holder
thingiverse

Pokemon Rare Card Holder