power pole surface mount 3d models

Anderson Power Pole Surface Mount version that provides cutouts in the lid vs the whole in the bottom. ...Cutout is sized to support up to 2x 6 gauge wires.

Anderson Power Pole Surface Mount. As the name suggest, this might come in useful at countless 12VDC applications where a surface mount is applicable. Overall height: 27.2mm M3 and M4 sizing Lives under my roof top tent for 12v power up in there. ... ...

This is a power strip mount for a 25mm pole. It is made to clip around the pole and velcro or double-sided tape to the power strip. The hole is 25 mm. The square mount is 29mm wide by 28 mm tall. ...

I didn´t like the power supply hanging around under my desk, so i designed a mount for it to go under the desk. Of course you can also mount it anywhere else. ...It should slide in and out easily but wont fall out by itsself.

Recommended only if you trust the power supply not to heat up and melt the mount, and if the surface being mounted to can really hold screws. most critics would deem this an unsafe accessory, so refer to the comments for feedback and advice. Screw...

Simple chassis mounts for Anderson Power Poles. I included the source files incase you want to modify them. ...From SketchUp Make 2015

Insert machine screws partway into the threaded holes on your power supply, and slip the unit on the mount bracket so that those machine screws fit into the slots. Please leave a comment if you think this model is unsafe to use. ...I installed this a...

This is a Panel Mount to hold the 15-40 AMP small sized Anderson Power Pole connectors that have become the standard +12DC Power connections in Amateur Radio. The mount is keyed to accept a pair of mated connectors in one direction only and the...

Bulkhead pass thru for a single Anderson Power Pole. ...Fits in 1 inch round hole, held in place with 2 screws.

Surface Mount for the LRS 350 Power Supply. ... 1/4 inch-20 hole

A 3d Model of a Power Module Surface Mount with dual outlet and USB charger created in Solidworks.

I needed such a Anderson power pole panel mount with a round plate to cover an M40 cable fitting hole.

This is an under-counter mount for the Microsoft Surface power supply (power brick). It was created to hide the power brick and extra cable under my kitchen counter, as I have a Surface RT as my smarthome control touchscreen. Although I haven't...

Bulkhead mount for a dual Anderson power pole connector. ...Mounts in 1.5 inch hole, held in place with 4 screws.

Building a kiosk or wall mounted Surface Pro? ...This mount will securely hold the power supply and still allow the ability to remove with a velcro strap if needed. Created for use with a Velcro strap like this. ...http://a.co/84U0KaB

Wall Mount for Surface Pro 7 power block I hope you like it and if you do leave a like and thank you for Downloading (Number 8) size screw used (hole are countersink) 8.32mm Outer Dimensions of the Hole and the Inner Hole is 4.52mm for the screw to...

This is a Panel Mount to hold the 15-40 AMP small sized Anderson Power Pole connectors that have become the standard +12DC Power connections in Amateur Radio. The mount is keyed to accept a pair of mated connectors in one direction only and the...

Fits well 12x19mm power switch.

Fits well 12x19mm power switch. ...

A panel mount for a pair of 15amp Anderson "power pole" connectors. screw some M3x6mm screws into the top for extra strength and insert a piece of 1.75mm filament into the hole to secure the plug. The dust cover should be printed in Flex or...

Modelled after typical Chinese "XH" (JST) surface mount sockets

Modelled after typical Chinese "XH" (JST) surface mount sockets

Modelled after typical Chinese "XH" (JST) surface mount sockets

Oldschool steel power pole Total height: 18m

Goku’s Power Pole and his granpa’s 4 Star Dragon Ball

This is the power pole given to Goku in Dragonball. There are 3 files. The short pole fits into the case which can be worn on the back of a Bandai Shodo action figure. You will need to tie a string around the indents in the case part for it to be...

This is the power pole given to Goku in Dragonball. There are 3 files. The short pole fits into the case which can be worn on the back of a Bandai Shodo action figure. You will need to tie a string around the indents in the case part for it to be...

I enjoyed the design but unfortunately my flagpole has ends that keep me from being able to slip it into the tube so i cut away the overhanging sections and made 4 rectangular holes that will allow me to use zip ties to keep flagpole attached.

Power Inlet Plug and Switch Surface Mount Box. This is one part of a set of parts. The goal for this project is to place all of the internal components from the Creality CR-10 control box on the underside of an Ikea Lack table with the printer...

I grew tired of my Surface Laptop's power connector pulling off due to it's weak magnet, so created a mount with extra magnets to make it stick better. I used 15 mm magnets, and have included a 8 mm size, but I will create mounts for other sizes, if...