powerspec ultra 3d printer

Looking at the design of the PowerSpec Ultra, the wires for the printing head are not well protected from stress. It appeared to me the single tie wrap to the bundle created a specific stress point. This design locks the conduit into an open tube to...

#### Uses: The PowerSpec Ultra is basically the internals cloned from the Flashforge Dreamer with the body cloned from the Flashforge Creator Pro (although I think some early models actually were full FFCP clones). Unfortunately, this means that it...

When I was working on the innards of my PowerSpec Ultra 3D printer I noticed that the fan that provides cooling to the mainboard was held in place by a holder that obscured 1/3 of its frontal area. ...This design fixes that problem !

This project allows you to print a custom top panel for a PowerSpec Ultra 3D printer with places for dual 120mm PC fans. This provides improved air circulation and cooling allowing you to safely print PLA plastic without removing the hood. ...Print...

I converted my PowerSpec Ultra 3D printer to use an SKR V1.4 Turbo with TMC2209 drivers, an ABL sensor and a TFT35 EV3.0.1 display. Due to the ABL sensor, I also converted the printer to use a single extruder/hotend. Since BTT ships little ducks...

I just started to print using PETG and needed to be able to control the PowerSpec Ultra 3D printer beyond the settings offered by PowerPrint, which is the application that comes with it. Since the printer is a clone of the FlashForge Dreamer in a...

With the holes in the top of the 3D printer, they simply needed filled with something! Not very creative, but the hangers are handy. I hang my side cutters, usb cables and small things like that on them. I will be creating more since there are...

My solution was to find a way to use the original spool holders, but relocate them to the side and use the existing holes in the printer to mount the hardware. I haven't tested this, but I believe you can also mount these on the back side if you...

I would recommend printing the inset one for the PowerSpec Ultra 3D and use the flush model if you want to modify it for other 3D printers. <h1>Motherboard:</h1> Switched from the FlashForge DriverBoard Rev F to a SKR 1.3. Print out four...

I made the filament guide tube clip to replace broken ones on the back wall of PowerSpec Ultra 3D printer. ...Print Settings Printer Brand: PowerSpec Printer: PowerSpec 3D Pro Rafts: No Supports: No Resolution: .2 Infill: 25% How I Designed This I...

... will be a tight fit, but it will indeed fit onto gantry. Print Settings Printer: Powerspec 3D Ultra Rafts: No Supports: No Resolution: Any Infill: 25% Notes: I designed it so that there's minimal bridging, it should print well with on most printers.

This is a screw in filament holder for the Powerspec Ultra Printer and should fit the ctc dual. ...works well , print vertically with extra shell and top layers.

... one plug - copy and paste away. It's an easy print with no supports and no raft. I printed it in ABS on a heated glass bed at 50% infill and ,1mm resolution. Print Settings Printer: Powerspec Ultra Rafts: No Supports: No Resolution: .1mm Infill: 50%

After a few years of use, the filament tubes no longer stay inserted into the retainer on the top of the hotend for my Powerspec Ultra machine. I bought new filament tubes, only to find that the wear was in the plastic piece at the top of the...

I've designed this Ultra portable 3D Printer to bring to ERRF2019. Many people enjoyed it, I have to make this design Open Source for you guys. As the space is very limited for every component, the assembly process is very time consuming. The use of...

I've designed this Ultra portable 3D Printer to bring to ERRF2019. Many people enjoyed it, I have to make this design Open Source for you guys. As the space is very limited for every component, the assembly process is very time consuming. The use...

A simple snap together (with a little help from a hammer) spool holder for the PowerSpec Ultra 2.0 printer. The original holders only work with spools that have large enough openings to fit over the bump ends of the holders, none of mine did so...

I purchased a different PWM controller and have a different printer, so I designed this for its power switch and potentiometer. I wired it to the stock blower fan, but you could also add a separate fan if you wanted. It comes with a three-way...

Offset spool adapters that allow a more snug fit of the lager spools. ...Its a 50mm outer bore so it allows for Matterhackers filament which is slightly smaller than the others I've used. GizmoDorks, IC3D, Inland, ColorFabb, 3D-Fuel, Hatchbox.

http://www.thingiverse.com/apps/customizer/run?thing_id=714444 Instructions Using the following options: baseheight_percent = .30 textsize = 16 textstring = PowerSpec 3D basethickness_percent = 0.2 font_catch_diacritical_sign = 2.3 do_shift_font =...

This is my third and latest 3D printer design targeting high quality, reliability, and moderate print speeds. It stands about 1.5 m tall and weighs about 35 kg. It fits into my Prius laying on its back, with the hatch closed. I can transport it...

Customized version of https://www.thingiverse.com/thing:1949142 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1949142

There are already a few designs of the filament guide for these 3D printers available. Most if not all are two sided (for left and right extruders) and installed with the existing straps. In my case, one of the straps is broken and I can't use it. It...

The arm pivots in a clevis and pin base, and hooks onto the bar post on the printer door. Mounting tape was used to stick the pieces once aligned. The arm is shown flipped back on top of the printer while printing ABS. Nothing special about...

After a couple of years that I follow 3D printer growth, I picked up all the best solutions, as magnetic joints and prismatic linear guides, and gather together in this project. A complete 3D Delta Printer that can be built with about 200 euro (with...

An IGUS style 3mm linear bearing, designed to print with .4mm nozzles. ...Print Settings Printer: Powerspec Ultra 3D Printer Rafts: No Supports: No Resolution: .15mm Infill: Doesn't Matter

-This is a led holder for Xhover MXP200-b 12V RGB 5050 LED Board -It just slides on the back standoffs of the Xhover MXP200 -Used Petg filament. ...-0.2 layer resolution -Printed with Microcenter PowerSpec Ultra 3D Printer

I am always developing my printer, trying to make it better. The newest adittion to the design is a light x-axis. The extruder is removed from the moving x-axis and placed on the frame. The design is made for pneumatic fittings. I use a bowden geared...

This is a derivative of the Dropcam Replicator 2 Corner Mount, I just made it fit to the PowerSpec 3D Pro enclosure. The credit remains with the original author. You can use it on any corner. Instructions As the mount is kept outside of the printer...

... and easy. Updates: Version 1.2 added proper holes to door to accommodate hardware listed below. Version 1.1 added 2mm to diagonal roof to close gap at front of printer. Marked top in file. ...Use a piece of tape to keep track before assembly.