printrbot pro 3d models

I built up a PrintrBot Pro Adoptabot from Brook for a local robotics club and a high school (a beta unit without the TinyG Controller, ribbon cables, wiring, and other parts). To wire it I had to make a simple loom along the right hand side in place...

this is a replacement foot for Printrbot Simple Pro.

This is a printrbot Simple Pro display adapter only to be used in conjunction with a printed housing like thingiverse design #2852928 by Joe Tisch or similar.

I built a Printrbot Simple Pro from parts, but didn't use a controller that used an LCD. I wanted to close the missing LCD hole and designed this to fit in that spot. ... The logo/text are remixed from motorbikemikexb9's "Printrbot Keyfob 3 color".

I bought a Printrbot Simple Pro Kit which did not come with the original rubber feet. I did not like those little feet on the Printrbot Smalls because they kept popping out all of the time. So I designed a foot bar that actually screws together. I...

I built a Printrbot Simple Pro from parts, but didn't use a controller that used an LCD. I wanted to close the missing LCD hole and designed this to fit in that spot. The logo/text are remixed from motorbikemikexb9's "Printrbot Keyfob 3 color". ...

The printer Brook donated used one of the F5 Printrboards instead of the G2 board used in the production Printrbot Pro printer. So in order to get Serial (Tx/Rx) working on the F5 board I had to compile the firmware with some edits. I have included...

A new front panel to mount a Hyperpixel Pi touchscreen to a Printrbot Simple Pro. Print vertically! (rotate the file 90° in Cura) Use support, should be easy to snap out. And brim, at it's tall and narrow. It'll be a tight fit, literally 1mm to...

Redesigned fan shroud for the Simple Pro

Redesigned fan shroud for the Simple Pro Print instructionsUnassociated tags: Fan Shroud, Simple Pro Category: 3D Printer Parts

Fan shroud that attaches to the 50mm blower fan on the Simple Pro extruder. ... See build instructions at http://printrbot.com/2016-printrbot-simple-build-instructions/

Replace your Printrhub on your Printrbot Simple Metal Pro with a Raspberry pi! Run OctoKlipper (and more?) in a fully enclosed portable printer! Cool right? You will need to solder power to the Raspberry Pi board. Two test points should be under...

Adapter to replace the extruder and hot end on a simple pro with a BMG geared extruder and E3D V6. Nuts and bolts required, just look through your parts bin. ...Print the two halves near solid for as much rigidity as possible.

The fan shroud for the Printrbot Simple Pro didn't perform as one would expect because with original design it was blowing straight at the hotend nozzle. When the fan was on above 75% it would cool the nozzle to the degree that it would override the...

E3D V6 hotend mount and cooling duct adapter for the Printrbot Simple Pro. Spaces out the hot end a bit to make room for the E3D cooling fins. The original hot end cooling fan bracket will need to be bent out of the way. Also added a couple extra...

Allows insertion of brass 8 mm flange nut after the flange has been turned down for clearance.Oh why did I sell that lathe? In any event, in this case the flange was crudely reduced by chucking in a drill and spinning against a bench grinder wheel.

6mm (2 X 3mm Baltic Birch ply) stacked wooden sub-frame to facilitate an aftermarket bed heater on bottom of original bed. The cut file now measures 300mm X 165mm to enable using a 12" X 12" Birch blank. The 3d printed belt ends are interchangeable...

"wire relief" by abdrumm blocks one screw that holds print bed to base, AND it uses screw to hold bed belt tight.. i did a cut n paste remix of his file so bed screw should not be blocked.. use at own risk ive not tried it yet !! fThis thing was...

Extruder Mount gives a little more rigidity to the fastening the extruder board to the printer. ...Fits nicely behind the extruder board and does not interfere with any of the electronics.

I grew tired of hearing the loud 30mm hotend fan, so I made this simple shroud that lets you mount a 40mm fan instead, which are much quieter. You can mount the fan directly without the cover, but the cover helps make it a little prettier and keeps...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/2zwOaNxjxBz

Holds the wires with zip ties, see pictures for reference.

<p>Remixed from goofdad's original. ...Added ball to accept ball &amp; socket mount from MoonDoggy's <a href="https://www.thingiverse.com/thing:2773810">https://www.thingiverse.com/thing:2773810</a> and cut a hole for access to bed mounting screw under...

Remixed from goofdad's original. ...Added ball to accept ball & socket mount from MoonDoggy's https://www.thingiverse.com/thing:2773810 and cut a hole for access to bed mounting screw under cable relief section.

you will have to leave the front cover off the printer but its worth the improvement in print quality. ...print with the outlet facing up

If you did not receive this part in your Simple Pro/Play v2 Heated Bed Upgrade, print it out to provide relief to your the thermistor cable that measures the temperature of your heat plate.

<p>A remix of <a href="https://www.thingiverse.com/thing:2773810">https://www.thingiverse.com/thing:2773810</a> by MoonDoggy (<a href="/MoonDoggy/about">https://www.thingiverse.com/MoonDoggy/about</a>) and <a...

A remix of https://www.thingiverse.com/thing:2773810 by MoonDoggy (https://www.thingiverse.com/MoonDoggy/about) and https://www.thingiverse.com/thing:2739523 by https://www.thingiverse.com/goofdad goofdad. I included all the parts from...

a part for printrbots

first thing i design and upload to thingiverse. ... Instructions download the stl file and slice and print