probe stick 3d models
79676 3d models found related to probe stick.thingiverse
Very easy fix if you lose or break the probe stick of the Artillery Sidewinder X2. Real issue is about weight of the part because it works thanks to a magnet, so print it like this: 0.4 Nozzle 0.12 for max resolution 15/20% infill ...
thingiverse
In the end of the stick is a small hole where I glued in a small micro push-button switch. The probe attaches to the hot-end holder that mounts to the X carriage. I'm uploading the 123d design source file too. Measure the thickness of your...
cults3d
This is a 3D printable, SI-8B (Си-8б) Geiger-Müller tube based, probe-stick. The handle is made of the 25cm long 25mm external and 22mm internal diameter standard aluminium tube. ... If you need contacts for the tube please contact me by message.
thingiverse
This is a 3D printable, SI-8B (Си-8б) Geiger-Müller tube based, probe-stick. The handle is made of the 25cm long 25mm external and 22mm internal diameter standard aluminium tube. ... If you need contacts for the tube please contact me by message.
thingiverse
Modeled after a nylon probe tool used to work with electronics to connect small parts or to hold model pieces in place waiting for the glue to set.
sketchfab
Little weekend probe project! ...Was inspired by the Protos probes of Starcraft! Just put my own little spin on it :) Game res. ...modelled in Maya then sculpted over in Zbrush, with textures coming from Substance.
thingiverse
Probe for Anycubic Kossel 3D printer, use a microswitch as sensor and plug it in the z_min end stop pin. Upgrade 3D printer firmware to make it work. To attach it to the plate use a magnet from a mechanic hard drive. ...With my microswitch (which is 11...
cults3d
Simply uses a M4 x 12 STEEL countersunk cap head bolt and a suitable T-nut to fix to any position you like on the 20x20 rails and the magnet in the level probe just sticks to the head of the bolt. ... After some feedback I've added a second design that...
thingiverse
Simply uses a M4 x 12 **STEEL** countersunk cap head bolt and a suitable T-nut to fix to any position you like on the 20x20 rails and the magnet in the level probe just sticks to the head of the bolt. ... After some feedback I've added a second design...
thingiverse
This probe sticks out below the bottom of the hot end is used for alignment purposes only. ... This is the config I used when it's connected to "E2 Stop" on the DuexBoard (Switch 5) M558 P4 C5 X0 Y0 Z1 H3 F50 T6000 S0.02 A2 G31 X2 Y40 Z0 P25 ...
thingiverse
Designed this after seeing the Alien Z Probe http://www.thingiverse.com/thing:820260 The probe sticks too far off the back of the effector making it run into my z-axis belt. Not useful for me but I think the design was good in thought. Perhaps...
grabcad
Stick _ 00.stl collected with EinScan Pro 2X Plus stick 01.objstick 01.stlcollected with NextEngine 3D Scanner.jpg image, and scan created by Caitlin Driver
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: stick_thickness = 2.5 flat_bottom = 2 stick_width = 8 font_size = 10 message = PNP Font = write/orbitron.dxf hole_radius = 3 font_thickness = 5
sketchfab
Subdivision Level: 1 Non-Mirrored. ...Textures: 32 x 32, One color on texture: Brown. Materials: 1 - Stick Formats: .stl .obj .fbx .dae .x3d Origin located on handle-center Polygons: 2222 Vertices: 1113 I hope you enjoy the model!
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=28771 Instructions Using the following options: total_length = 100 ornament_thickness = 2 stick_diameter = 2 ornament_size = 0 cone_length = 0
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=28771 Instructions Using the following options: stick_diameter = 3 ornament_size = 0 ornament_thickness = 0 total_length = 50 cone_length = 10