ps4 controller mount for iphone 3d models

PS4 Controller Mount for your IPHONE x works with Siliconcase ! ...

FeaturePerfectly fits PS4 controller and iPhone 12 miniPS4 controller clip into place, no rubber band neededPrint without supportReferencethe PS4 controller dimensions are taken from...

V1.2 Dualshock 4 / PS4 controller mount for iPhone. I made this so I could stream pc games on the go to my phone using the Steam Link and moonlight apps, I wanted a single piece mount that was simple and ended up using a thick rubber band to hold it...

This is a mount for the PS4 controller with a bracket to fit on the IKEA Expedit shelf

Ps4 Controller Wall Mount

PS4 Controller and Headset Mount

A wall mount for neat storage of your PS4 controllers

Mount PS4 controller to shelf or to cabinet. For 17 mm cabinet wall thickness. ...No needed screws or glue.

Simple ps4 controller desk mount for a 40mm thick desktop. ...Easy to move no need for screws or permanent fixtures, supports itself.

I give you this PS4 controller wall mount. It consists of 2 pieces, the recessed and the hook that takes the PS4 controller. The wall mount does not require a bracket for manufacturing. ... The hook of the controllers does need support for the...

A 3D printable controller mount for the ps4 controller, the model has to be printed on its side ( as shown in the picture ).The mount is attached to the wall with double sided tape.likes are appreciated as always

The controller mount is perfect for the PS4 controller from Sony. It convinces with a simple and plain design. ... Feel free to check us out on Instagram @print.compact.

This is a wall mount for one or two PS4 controllers. Works well. If the biggest part get above the bed it will print well without supports. ... Hope you like it.

HAVING NEVER BEEN QUITE SATISFIED WITH THE DESIGN OF OTHER MOUNTS FOR MY PS4 CONTROLLER, I FINALLY GOT AROUND TO MAKING A NICE SLIM PROFILE ONE THAT ALLOWS THE CONTROLLER TO BE PLACE UPRIGHT, ALLOWING THE CHARGING CABLE TO BE ACCESSED/PLUGGED IN WITH...

This is a wall mount for your PS4 controllers, this mount is designed to keep your controllers close to the wall. I hope you enjoy! Print Settings Printer: Da Vinci Pro 1.0 ...

A wall-mount adapter for the Playstation 4 Dualshock 4 controller. The original USB cable clips into this thing. My cable clipped in very snugly, but if yours isn't so clicky, maybe a dab of glue would help? The USB plug clicks into the controller...

### Goals for project - Open source the files - Easily Editable and customizable - Establish/initiate correct format of documentation ### Important links - Thingiverse link to original [files](https://www.thingiverse.com/thing:3158960) - OnShape cad...

This is a PS4 controller mount I made for the same "Clip System" I made for my headphones. (here: ==>>http://www.thingiverse.com/thing:693980) The main base clips onto the glass table, then the mount part slides into that clip and the hooks press fit...

The controller mount fitted well but had some issues for me. As the fit was good it was difficult to take the controller out, requiring both hands to grip either side of the controller. I removed the middle section so it is easier to grab the...

This is a PS4 Controllermount for the IKEA Alex Drawer and under Table ( Shelf )

V1.2 Dualshock 4 / PS4 controller mount for iPhone. I made this so I could stream pc games on the go to my phone using the Steam Link and moonlight apps, I wanted a single piece mount that was simple and ended up using a thick rubber band to hold it...

Click-in DualShock 4 wall mount.Created this because I couldn't find one which can hold the controller upside down.See also the one for the DualShock 3: https://www.prusaprinters.org/prints/149786-ps3-controller-wall-mount

This is a ps4 mount I made because I could not find one that was stable horizontally on Thingiverse. This one is wide and uses less material than some. ...It can mount to the wall with command strips or the screws holes in the part.

Slimmed down the original in all directions and put a small angel for the back of the controller to rest into. Also filled the screw holes as I'm using Command strips to mount. ...

... by araymbox. ...I didn't need the controller to clip on and I didn't need the screw holes because I use Command Strips. I removed the clips and adjusted the angle a bit for the controller to rest comfortably without forceful locking into position.

I needed a mount for my controller since there is none on this website, I tried making my own. You can use the controller stick caps or without - works both! I personally have mounted it with a Powerstip to my desk because I dont want holes in my...

I remixed these two as i liked the design of the PS4 holder and the idea of a under-desk-mount. Removed the audio jack (symmetry) as I didn't need it. Changed the bracket to fit a IKEA Malm desk and made a fitting top and back plate. !! The...

I remixed these two as i liked the design of the PS4 holder and the idea of a under-desk-mount. Removed the audio jack (symmetry) as I didn't need it. Changed the bracket to fit a IKEA Malm desk and made a fitting top and back plate. !! The bracket...

PS4 The STL is changed, i made a mistake in the construction.

A wall mount is an easy way to protect your controller when you have kids at home! About 50 min printing. ...Print Settings Rafts: No ...