qidi tech x maker 3d models
358811 3d models found related to qidi tech x maker.thingiverse
3d printer Qidi X Maker not for 3d printing, but for architecting enclosures and test benches available in Solidworks file, STEP and STL file.
thingiverse
This is my cooling upgrade for the QIDI-TECH X-MAKER (I believe it should fit X-MAX and X-PLUS since they have same extruder). The original part cooling has an internal 5015 fan but it's airflow is very poorly guided to the actual printed part. ...
cults3d
Stores all your tools for the QIDI Tech X-maker 3d printer. Also holds your USB storage and small snips. ...This model is unlocked so you can ungroup and revise it.
thingiverse
Filament roll holder for the Qidi Tech X Max. The original telescopic tubes and the spool holder are reused. The PTFE tube at the filament inlet is inserted into the tube holder. ...The filament roll is now much higher, so it no longer breaks and can no...
thingiverse
Because I was not very satisfied with the standard spool-holder of the Qidi X-Max, I designed a new one, where the roll change is very easy. Additionally you need 2 round steel bars with 6mm diameter and 218mm length. Furthermore I recommend 4 ball...
thingiverse
A mounting adapter for the Bewinner USB Webcam (https://www.amazon.de/gp/product/B07N392J1S/) for the QIDI X-Maker.
thingiverse
Qidi tech X Plus - top cover closing plate - with thermometer hole, with filament hole or just blank. ... As thermometer used Afriso 63826K - 0-60 grad
thingiverse
Designed to help assist with bed leveling for Qidi Tech. X-Plus. Squares are large format 50x50mm and printable area is 250x180 mm. ... Designed to be printed on a single layer with a .04mm nozzle at .02mm layer height.
thingiverse
Designed to help test bed level settings on Qidi Tech X-Plus. 3 rows of 50x50 mm squares to show where adjustments are required. Designed to be printed with a .04mm nozzle at .02mm layer height. ... Printable area is set to 250 x 180 mm
thingiverse
This is just a ROUGH model of the frame of the Qidi Tech X-one 3D printer. I used a tape measure to take most of the measurements, so use this at your own risk. ... I made this model so that I could design an enclosure around it.
thingiverse
Playstation Eye Camera Mount for the Qidi Tech X-One. The camera mounts to where the handles would normally be. There's a friction fit to the camera, but I also used some hot glue to hold it in place. ... PS Eye Camera ...
cults3d
the default attachment of the wire guides of the QIDI TECH X-PRO printer (model 2019/2020) is glued to the bulkhead, which sometimes causes problems. This model allows the thread guide attachment to be offset from the middle of the spool and mounts...
thingiverse
These squares are used to level the build platform of the Qidi Tech X-one2. Print at the recommended temperatures for the filament you are using. Print at 0.2 mm layer height. These squares will only print one layer and you can use this to help level...
thingiverse
I broke one of the blades in the stock extruder fan on my Qidi Tech X-One. I replaced the 40x40x10mm fan with a 40x40x20mm fan. https://www.amazon.com/gp/product/B075SL6RYQ/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1 I used two M3x50mm flat...
thingiverse
This is a remix to fit the new Qidi X-One2 model without the metal handles on the side. Can be printed on 3 beds or use the "Full Holder" file to print all 3 on your bed at the same time (its about a 12 hour print all together). ... Print all three...
thingiverse
This adapter will enable you to use a filament spool with a [roughly] 3 inch hole on the Qudi Tech X-One2 filament spool holder that came with the printer (which has a [roughly] 2 inch hole).
thingiverse
... to bed. ... There are a lot of flaws with this design, but it serves my purpose. Uploaded a picture of it in action, make note my how my bottom bed plate is orientated, some Qidis its reversed from this. ... Included is the Camera Holder that I use.
thingiverse
... are quite large and do not fit several brands of spools. ...Here is one that has an easy twist off cap for holding spools. Required is a M10 x 1.5 x 20mm bolt to hold it in the printer. ...There is already a recess to hold the bolt hex head for you.
thingiverse
pla bushings for the 8mm rods for the X/Y axis , you need a total of 8 to replace all b8 = 8mm id b8.05 = 8.05 id b8.1 = 8.1mm id b8.15 = 8.15mm id b8.2 = 8.2mm id the more accurate the printer is the smaller the id you can use , I find 8.05 perfect...
thingiverse
New Version. ... The X maker has a different maybe new carriage. ... Fits both now
thingiverse
It is a phone mount for the Qidi tech X-max and X-plus. You would need to use attached custom start and end g-codes in Cura (or whichever software that allows them). Otherwise the extruder will hit the mount during initial priming. ...
thingiverse
It is a phone mount for the Qidi tech X-max and X-plus. IMPORTANT: You will need to use attached custom start and end g-codes in Cura (or whichever software that allows them). Otherwise the extruder will hit the mount during initial priming. ...
thingiverse
I was disappointed with Qidi's "baggage handle" spool holder, as it introduces a lot of friction which leads to inconsistent extrusion, especially with flexibles. A quick trip to Tinkercad, and we have a solution! It takes two (total) of 608-sized...
myminifactory
Housing for LED Switch on QiDi Tech X-ONE. Check out my review of the X-ONE: https://tinyurl.com/TrustedTechReviews
thingiverse
A simple extension for the Qidi Tech X-Pro spool holders, because they are too short for 76.2mm (3 inch) spools (e.g. ...AmazonBasics).
thingiverse
... and cut out the right side as shown to get rid of the original cooling duct inlet. ...This part will also interfere and replace the extruder cover since it is thick enough to also act as the surface for the X-axis limit switch to press against.
thingiverse
Part Cooling Fan Shroud for QIDI Tech X-One 3D Printer. Dual cooling ports and replaces the stock fan with direct bolt on fit. Recommend printing with ABS or PETG at at 45 degree angle. ... See image example for part orientation in slicer.
thingiverse
This part is specifically designed to fit the Qidi Tech X Pro. I created it because the new all metal hot-end heater tube is much shorter than the stock one, therefore the nozzle was too short for the stock turbo fan duct. This is a revision on a...