qo onos 3d models
137 3d models found related to qo onos.thingiverse
Customized version of https://www.thingiverse.com/thing:2733619 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2733619
thingiverse
Relatively easy to build QO-100 uplink helix antenna for the hamradio 13cm band (no satellite dish required). This antenna is good enough for QSOs in SSB (SNR 13 db on the websdr). For the downlink you can listen to a QO-100 websdr. Building...
thingiverse
I present you a QO-100 poty antenna protector. You need to buy separately the "bubble" that will be in front of the antenna. You can find it at this place (at least in France): ...
thingiverse
I present you a QO-100 poty antenna protector. You need to buy separately the "bubble" that will be in front of the antenna. You can find it at this place (at least in France): ...
thingiverse
This is a spacer (you need two) for putting a 22mm Pipe feed into a 40mm satellite LNB holder. ...Generally used with a Patch Dual feed on Amsat QO-100 / Eshail Satellite. Personal Ham Radio use only please. ...NOT for commercial reproduction.
thingiverse
Dual feed ("Ice Cone Feed") for QO-100 satellite ground station. See my QRZ page for detailed instructions: https://www.qrz.com/db/DO8PAT#IceConeFeed This is an open source project for the HAM community. Please respect the non-commercial license...
grabcad
The Eye of Qo'noS (Cronos) is one of the most important relics on the home planet of the Klingons. The eye is made of a piece of glowing Ptáchoch, dug out of the molten heart of Cronos and caught in a graviton field. The deadly radiation is shielded...
cgtrader
... Weights Everything in Turbosmooth, if you wish, you can reduce iteration. ... Product Link: https://www.1stdibs.com/furniture/lighting/chandeliers-pendant-lights/florian-schulz-double-onos-55-pendant-lamp-side-counter-weights/id-f_15702151/ Good luck
cgtrader
Name: Mint_Florian_Schulz_Onos_Polished Version: 2013 Units: Millimeters Dimension: 297.35 x 158.46 x 394.8 Polys: 3 795...turbosmoth 1 iteration _ 30 278 Model Parts: 1 Render: V-Ray Formats: 3Ds Max 2013, OBJ
thingiverse
Housing for QO-100 POTY-Patch antenna in combination with DN 110 end cap
thingiverse
This adapter ring fits perfectly for DXPatrol QO-100 LNB with 55mm This is not my own design. ... Credits is only for https://www.thingiverse.com/thing:3899461
thingiverse
QO-100 / P4-A / Es'hailSat / Es'hail-2 - LNC-Mount 23mm for Kuhne MKU LNC 10 and BaMaTech Duoband-Feed V2.0 from DJ7GP with 1x or 2x 10GHz. Available for one or two LNC's. Requires following Screws available in your Hardware-Store. 2 x Socked...
thingiverse
This is a rain protection cover for an qo-100 helix antenna. The antenna is originally published here: https://www.thingiverse.com/thing:3849410 Just put this over over the helix. ...
thingiverse
This is a rain protecting cup for QO-100 patch feed. The diameter of the patch is 105mm. The distances between the four cuts are 100mm. ...(at the screws)
thingiverse
This Thing is designed to replace the LNB holder on a Gibertini style satellite dish boom to mount a BaMaTech LNB and a Kuhne electronic MKU LNC10 QO-100 down-converter. The LNB base mounting part provides a skew angle scale to align the LNB...
thingiverse
QO-100 / P4-A / Es'hailSat / Es'hail-2 - Excentric Reduction-Ring from 40mm to 23mm for BaMaTech Duoband-Feed V2.0 from DJ7GP with 1x or 2x 10GHz. Available for Schwaiger, Triax or Univeral-Dishes. V1 is one piece non-latching V1-1 is one piece...
thingiverse
Case for the MiniTiounerPro V2. Base and cover designed to enable easy access for installation of board and tuner. Depends on print setup and printer type you may need to slightly trim the hols. Note that you may need to apply some pressure...
thingiverse
Well, during my QO-100 satellite experiments I was fed up with many small 12 volt adapters. So I created this adapter with many connector on the front. ...Inside there is a 5A 12V brick normally used for LED lights.
thingiverse
This is an enclosure for Dxpatrol.pt's upconverter MK2.
thingiverse
This thing was made with Tinkercad. ...Edit it online https://v1.tinkercad.com/things/i3Yz2lIXX1t
thingiverse
This is an interlock I designed after seeing a similar layout for a GE load center but couldn't find one for my particular load center. This design will not allow the generator to be on at the same time as the main circuit breaker thus preventing...
thingiverse
Remixed front from DX Patrol upconverter case MK3 by mucsb for MK4
thingiverse
This is an enslosure for the up-converter panel from DXPatrol.pt. This is for MK2. As they sale the panel with no case I thought this could be useful for other HAM mates. Good luck for printing. Should you need a ready made printed instance...
thingiverse
This is an enslosure for the up-converter panel from DXPatrol.pt. This is for MK1. As they sale the panel with no case I thought this could be useful for other HAM mates. Good luck for printing. Should you need a ready made printed instance only...
thingiverse
This is a stencil to paint spay (tag) satellite dishes...or other objects.
thingiverse
<h1>Thanks for a TIP</h1> <h1> Or a coffee?</h1> https://buymeacoff.ee/dm4ds Hello and thanks for the amazing interest on @twitter Here is the BamaTech Rain-Cover and some information about it. The files for the V1 version without lens...
thingiverse
Mount one or two Kuhne MKU LNC 10 on a DJ4GP-Feed V2.0 See also new Version on https://www.thingiverse.com/thing:5063132
thingiverse
<h1>Thanks for a TIP</h1> <h1> Or a coffee?</h1> https://buymeacoff.ee/dm4ds Hello and thanks for the amazing interest on @twitter Here is the BamaTech Rain-Cover and some information about it. The files for the V1 version without lens...