qrpguys 3d models

Case for the QRPGuys Mini Keyer V2 **6/5/19** Updated design to snapfit.

... same PCB / circuit board. ... includes nut for PCB mounted BNC connector https://qrpguys.com/qrpguys-11-41-voltage-baluns requires: Qty 3 of M3x25mm bolts Qty 3 of M3 nuts may require some fitting (sanding, ect) the nuts are press fit into the case

... was the design I came up with was small and lightweight. Almost as minimal as I could design. I'm sure it could be better, but it works great. Very tight fit. You can order the kit to build one yourself at: http://qrpguys.com/qrpguys-code-trainer

This case is designed to work with the new QRPGuys AFP-FSK Digital Transceiver III: https://qrpguys.com/qrpguys-digital-fsk-transceiver-iii There is a small window to allow you to see the xmit light along with inset labels for all the switches. It...

this is a base with handrest for the QRPGuys Single Lever Paddle w/Base. it provided a solid base for the hand to rest on when sending. ... i used double sided tape to hold the wedge and base to the platform.

Case for QRPGuys 10/20/30 dB 50Ω Switched Attenuator.

... based on a design by Charlie Lofgren, W6JJZ. The QRPGuys implementation is very good but it is lacking a proper case, hence my design. Posts for symetric feeding lines can be added in the back of the case. ... Best 73 de Toni, EA4LE / KC2HAX

This is a wire winder I made to hold the 49:1 transformer box kit by QRPGuys Mini No Tune 80-10. ...It holds the 28' of 24 awg wire for a 20m setup nicely and there is room for more.

This is a case for theQRPGuys Digital Power/SWR Meter w/Dummy Load: https://qrpguys.com/qrpguys-power-swr-dummy-load I adapted the base from https://www.thingiverse.com/thing:2732849 and designed the top. The top. now includes vents and you have a...

This box is made to fit the QRP Guys EFHW mini tuner. There is room enough in the corners for binding posts. ... You could extend the LED of the circuit board to make it protrude through the case, but not necessary.

https://www.thingiverse.com/thing:3958912 has LED holes for the older model. I closed both holes with Meshmixer. ... You will need to print the bottom from the original.

Here are bases for the Iambic Mini-Paddle Morse Code key and Single Lever key for ham radio sold by QRPguys.com. I love the keys but wanted a strain relief for the cable and enough of a base to attach Scotch Fasteners (like Velcro) to the bottom so...

I added a hole so you can view the LED and labeled the 3.5mm jacks IN for key or paddle and OUT for headphones/speaker.

Housing for QRPGuys DSB Digital Transceiver More info for transceiver: https://qrpguys.com/digital-transceiver?fbclid=IwAR0_OBlVr6jbS20eRED3Mg60macnNCtPC6NMcCevtJUy1_PB8TmkAVOe64M Print the text with a laser printer on a transparent sticker, then...

... gauge antennas like 26AWG. https://qrpguys.com/qrpguys-end-fed-wire-antenna https://qrpguys.com/qrpguys-multi-band-end-fed-antenna https://www.sparkpluggear.com/shop/p/sparkplug Unbranded because who wants someone else's callsign on your gear?

... small gauge antennas like 26AWG. https://qrpguys.com/qrpguys-end-fed-wire-antennahttps://qrpguys.com/qrpguys-multi-band-end-fed-antennahttps://www.sparkpluggear.com/shop/p/sparkplug Unbranded because who wants someone else's callsign on your gear?

It is a redesign of the approach of an antenna marketed by QRPguys and developed by Joe Everhart, N2CX: http://qrpguys.com/qrpguys-tri-band-portable-vertical-antenna. My approach differs in the following ways from the original one: 1. I use...