quadcopter parts 3d models
541496 3d models found related to quadcopter parts.thingiverse
These are files and parts for the Flitetest Knuckles H quadcopter and Anycopter I've made at Techshop. The laser cut parts are available from flitetest if you don't have access to a laser cutter.Or the PDF has the plans you can glue to a paper and...
thingiverse
Two parts: - A stand for standard brushless motors, at the end of a 22mm carbon tube - A clamp for 10mm carbon sticks as landing gear, clamped around the same 22mm tube The motorstands are glued at the end of the tube. The three wires are guides...
thingiverse
Some parts I made up for an iNav based quadcopter on the Lisam-210 carbon frame. ... The GPS mast cover doesn't snap on, so to attach the GPS board (BN-880ish sized) to the base, I used double sided tape, then another piece of the same tape on top...
thingiverse
... 07/May/2019 - update Pixhawk Mount, Electronics Bay, Pixhawk LED Dome, XT-60 Lipo-Battery Lock - new files added. Electronics bay also divided in to 2 parts for easy printing (part 1 and 2). Please like it if you download. ...Thanks :-)
thingiverse
Quadcopter Motor Mount Part for Hobbyking Super Mini Quadcopter Frame with Motors (445mm) Just test !! ...Not yet tested.
thingiverse
Handle has 25mm x 35mm, it should fit standard LiPo 3S small quadcopter battery, I use 1300 and 2200 mAh 3S turnigy, the difference is in length, so the smaller battery fits nicely but bigger sticks out a bit. Handle has 14.5mm of length, it had...
thingiverse
Repurpose your spare quadcopter or RC airplane parts to make this desktop solder fume extractor! Here it is in action: https://www.youtube.com/watch?v=VG0oGK6q3KU I got sick of solder fumes wafting up into my face, so I designed this fan to...
thingiverse
Created for QuadCopter build class at HackerSpace Charlotte Controller - AeroQuad Mini Receiver - Hobby King TR6A v2 Motor - hexTronik 20gram Brushless Outrunner 2300kv ESC - Turnigy PLUSH 6A Battery - Sky Lipo 1300mA 2 cell Version 2 of...
youmagine
Here are the parts in my build: Frame: https://armattanproductions.com/pages/kit_detail/2140 Frame takes m2 hardware with 22mm standoffs (see link below) Flight Controller:...
thingiverse
--- ***Edit 1*** Updated to have taller stand offs to give the go pro more room to move up or down also increased space by .1mm between the parts that the go pro mount intersects with. --- ***Edit 2*** Added more drafts to the initial go pro camera...
thingiverse
The basic design of the Micro Long Range (MicroLR) https://www.thingiverse.com/thing:4054381 .Camera have 2 models , 14mm and 19mm . ...XT30 connector with VTX antenna 10+ minutes of flight time (10mins of cruising on 850mah 3S)
thingiverse
I am a beginner, designed this main gear for a friend drone quadcopter. It work! ...
thingiverse
... and the outer radius of the shape is 3mm using the same centers. Print Settings Printer: Geetech G2S Pro Rafts: Doesn't Matter Supports: Yes Resolution: 0.2, 0.1 or even division of Infill: 35-100% Notes: you will need active cooling for both parts.
grabcad
This part is designed as a spare part to be printed and fitted on the frame. It was successfully printed without any printing flaws. ... Feel free to contact me to model any spare part for you.
thingiverse
Two parts I designed for the U180MM frame from aliexpress. Other solves the problem of where to mount the battery and the other enables you to have LEDs on your "top" arm. ... Print the ledmount vertically without supports.
thingiverse
There are some other copters available on the market using nearly the same parts but have different labels/names. Here it is just necessary that the arms have a 4x4 mm profile. I made a bracket for the arms that is able to engage in different...
thingiverse
70 grams, depending on printer settings/material), single print, 236mm quadcopter frame. Your power distribution board and naze32 flight controller can easily be attached with nylon m3 spacers. The esc's and receiver can be attached to the frame...
thingiverse
This is an F-117A Stealth fighter inspired quadcopter, which is completed using parts from the Tarantula X6 toy quadcopter. Designed to be printed as 7 separate parts and assembled using small screws. Various holes and slots are designed in to...
thingiverse
Free Parts! Here is the free download for all of the 3D printed components from the AeroX vertical arm FPV racing frame by Tetra Drones. Printed with Sainsmart TPU filament at 225*C. ... Check out the frame at: www.tetraairframes.co.uk
cults3d
This is my version of a V-tail copter. Im useing 1000 KV Motors and 12 amp ESC's as well as the Crius Multi Wii SE control board. This thing flys very well. I built a few Quad X copters, but it is very easy to lose orintation with them because they...
thingiverse
This is my version of a V-tail copter. Im useing 1000 KV Motors and 12 amp ESC's as well as the Crius Multi Wii SE control board. This thing flys very well. I built a few Quad X copters, but it is very easy to lose orintation with them because they...
thingiverse
My friend lost control of his quadcopter and the part which held the horizontal landing leg to the vertical landing strut broke. There was also a stress fracture on the horizontal landing leg , so I designed this part to replace the connector, while...
thingiverse
Wider battery mounting bracket New cover for copter, smaller for Naza m lite flight controller New base for Naza, power unit and radio Of course there is crash video http://youtu.be/OUwOLzE_50w my quad copter stress test continues (everytime I...
thingiverse
Instructions For the deck and top plate, print 2 of each piece to make the whole part. I used 4-40 machine screws and blind nuts to bolt the 2 halves together. You could add CA glue to the parts before bolting for a more permanent bond. Arms print...
thingiverse
The middle of my quadcopters shown here are from www.flighttest.com which they have available on thier website forum. Or you could design your own. The motor mount has gone through some revisions. I had to beef up the landing gear so they...