raise3d n2
1158 3d models found related to raise3d n2.thingiverse
Modification of my desktop spool holder to fit inside the Raise3D N2 printer. ...
thingiverse
improved air intake for the electronics of Raise3d N2 Set scaling to 1000%
thingiverse
This is a smaller spool holder for the Raise3D N2 printer. ... This is designed similar to the factory holders for 1" diameter spools.
thingiverse
... default. Print Settings Printer: Raise3D N2+ Rafts: No Supports: Yes Infill: 60% Notes: You may need a raft if you see any corner lifting. ... I didn't need to scale the object at all but you may need to make adjustments if using other materials.
thingiverse
My Raise3d N2 has been very good to me, but it needs a little rise in the lid design to clear the bend in the filament tubes as they enter the extruder. I use mostly PLA, but where the N2 sits is near an AC duct and the N2 needs the lid. I made...
thingiverse
I was having problems with air printing on my Raise3D N2 right extruder (dual setup). I tried loosening the screws that hold the acrylic panel on the front of the extruder, but it didn't solve the problem, so I scanned and traced the panel and...
thingiverse
This is an Indicator Holder for a Raise3D N2 or N2 plus. It allows for indication at nozzle location for 100% of print surface. NOTE: be careful and max travel in the X Axis, holder will hit Pillow blocks! Otherwise works great! Enjoy. I have...
thingiverse
Room air tunnel to cool motion control board for Raise3d N2. ...Fastener holes are small, enlarge as needed
thingiverse
... shorter shaft version (65mm) for the Microcenter Inland brand spools. ... I believe eSUN and many other brands use the same spool configuration. Print Settings Printer: Raise3D N2+ Rafts: Doesn't Matter Supports: No Resolution: 300 microns Infill: 30%
thingiverse
Note! ...Different revisions available! STLs for project titan extruder on Raise3D N2 machines. ...Follow along here: http://forum.raise3d.com/viewtopic.php?f=4&t=636
thingiverse
Print Settings Printer: Raise3D N2 Rafts: Doesn't Matter Supports: Yes Resolution: .2 Infill: 15 Notes: 4mm holes are added in the rear bump out to allow m3 x 5 push fittings. The handle pushes nice and tight into the acrylic door cutout. In the...
grabcad
This is a universal adapter to accommodate the Raise3D N2 printers specifically fitted with the Mosquito Hotend from Slice Engineering. Recommend CNC Machining using AL 6061-T6 or possibly Brass C360 with Electroless Nickel Plating. ...The Mosquito is...
thingiverse
This block can be printed and use to hold the Extruder temperature prob and heater bar out of the way on the Raise3D N2+ duel printer. We discovered that the duel extruders caused a lot of shifting layers. Removing the second extruder solved this...
thingiverse
This thing will be discussed in detail on the 3D Printing Today Podcast: threedprintingtoday.libsyn.com or search the iTunes music store or stitcher radio for "3D Printing Today" This thing is a modification of the Raise3D N2 and N2+ bed. The bed as...
prusaprinters
This thing will be discussed in detail on the 3D Printing Today Podcast: threedprintingtoday.libsyn.com or search the iTunes music store or stitcher radio for "3D Printing Today" This thing is a modification of the Raise3D N2 and N2+ bed. The bed as...
prusaprinters
This is a model of the large format Raise3D N2+ Print Settings Printer Brand: LulzBot Printer: TAZ 5 Supports: Yes Notes: Rotate model 90 degrees on the X axis to minimize supports Category: 3D Printers
thingiverse
**SUPERSEDED: https://www.thingiverse.com/thing:3440161 As you may notice there should be two free fan plugs on Raise3D N2 printers which can be used for the additional two fans. May require some gapping for the limit switch but I will update where...
thingiverse
... I stuck a little felt pad on each top bit, so I can just nudge the lid up and the props fall down without hurting anything. Thanks for the inspiration, Julia! Print Settings Printer: Raise3D N2 Rafts: No Supports: No Resolution: 0.2mm Infill: 25%
thingiverse
This is a replacement door handle for a Raise3d N2 with 5mm threaded screw holes. It will probably fit other 3d printers made by raise3d but I haven't looked at the dimensions for the slot on the doors of those printers, the n2 is about 1.5 inches...
thingiverse
This model is something I created because one of the corners of a Raise3d Printer I am using broke. This slides well over the side of the corners, and can be secured with silicone, glue, or can be left without it. This is my first design using any...
thingiverse
This upgrade is meant to be installed on the N2 but I tried it on an N2+ Frame. It's just a bit top-heavy but rolls great on anything but thick carpet. I used the Harbor Freight 3in Casters linked here:...
thingiverse
filament funnel guide for raise3d n2 and n2 plus Use super glue after assembled Print Settings Printer: raise3d n2 and n2 plus Resolution: .15 Infill: 15 percent Notes: funnel facing up on bed including hole on retainer box
thingiverse
This is a fan grill for Raise3D N2-N2+ printers (35mm fans) that snaps very easily onto the fan's frame.
thingiverse
Print in ABS Print Settings Printer: Raise3D N2 Plus Rafts: Yes Supports: No Resolution: 0,2 Infill: 20
thingiverse
This is an air tunnel for the Raise3D N2 / N2 Plus for better cooling of the motion board. Inside is printed with ABS Outside is printed with Polyflex In addition, we also use a piece of activated carbon for air purification. ... www.okm3d.de
thingiverse
... this as a precaution so it doesn't happen again. Print Settings Printer: RAISE3D N2+ Rafts: Yes Supports: Yes Resolution: .15 Infill: 25% Notes: I used RAISE3D PLA at 205 degrees. ... Custom Section
thingiverse
... longevity, but so far my ABS printed part seems to be holding up ok after about 30 hours of printing. I will replace it as soon as I finish machining the permanent mount. NOTE: This only works with the single extruder version of the Raise3D N2/N2+.
thingiverse
Remix of the EXCELLENT https://www.youmagine.com/designs/um2go-um2-low-friction-spool-holder Need : 2 x 608 bearings 1 x M8 threaded rod x 77mm 2 x M8 nut (better with 1 nylon stop and 1 std) 1 x 8,50 mm washer left and right element available with...