ramps board 3d models
87769 3d models found related to ramps board.thingiverse
Just in case anyone needed a spacer for this ramps board to shift away 20cm so it will not hit your X-axis stepper motor as it is raising up in the z-axis This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/jhqa6WlBumv
cults3d
so i designed the ramps holder and associated bridge board to remove all the wire clutter that i had on the side. i now use a case with enclosed ramps and display.. makes life easier to transport and use .. fits any ramps/arduino mega shield ..
thingiverse
so i designed the ramps holder and associated bridge board to remove all the wire clutter that i had on the side. i now use a case with enclosed ramps and display.. makes life easier to transport and use .. fits any ramps/arduino mega shield ..
thingiverse
It was used to hold the Arduino and Ramps 1.4 boards in the bottom of the printer. Because the USB cable had to attach to the Arduino board and also be able come out in between the two sections of the 20x20 rail, the board holder was slanted up...
thingiverse
Instructions 1) Mount the body to the frame of your printer 2) Add the boards 3) Attach your wires. 4) Attach the door. Door is optional. It attaches with 5mm bolts. Both the case body and door have holes for 40mm fans. ...I have my top fan blowing...
thingiverse
Sometimes the stepper drivers on the RAMPS board get a little warm which could possibly damage them. This is a solution for that problem that lets you be more at ease during those long prints. ...clips onto the acrylic frame for your Prusa i3.
thingiverse
There is room between the Ramps board and the fan for all the wires to be routed up or down the frame. But don't blame me if you don't pay attention to the possibility of wires touching the fan and wrecking something. I only print ABS so the Ramps...
thingiverse
Cover for the stock Ramps 1.3 board on the Hictop i3 clone (2015 model).
prusaprinters
Cover for the stock Ramps 1.3 board on the Hictop i3 clone (2015 model). Print Settings Printer: Hictop i3 clone Rafts: Doesn't Matter Supports: Yes Resolution: 300u or to taste Infill: 20% or higher Category: 3D Printer Accessories
myminifactory
As a part of building the 'Atomic U300' 3d printer, I designed a new controller case for the RAMPS 1.5 board. This case holds a power switch and a cooling fan for the RAMPS 1.5 and DRV8825 chips. The cooling fan is connected to the power line...
thingiverse
As a part of building the 'Atomic U300' 3d printer, I designed a new controller case for the RAMPS 1.5 board. You can use this case for any other 3d printer built with the 2020 aluminum extrusion frame. This case holds a power switch and a...
thingiverse
This was a quick design for a 40mm fan mount for the Ramps 1.4 board. Depending on how good your printer is, you will probably have to file out the grooves on the legs to ensure a good fit. *Update 7/3/2013 Added more material to the gripper...
cults3d
Support This support consists of a base that is fixed by pinching the RAMPS card and serves as a guide wire and a fan door that clips on the base. The fan is attached to the fan door by 4 bolts M4 x 25 and 4 nuts. The zip is composed of 3 files:...
thingiverse
this fan mount clips directly onto the RAMPS board and stays in place without wobbling. ... It requires two M3x20mm allen screws and two m3 nuts to mount the fan.
thingiverse
Mounting plate for RAMPS board that comes with the Hictop 3DP-12 (MKS 1.3). Needed something simple without special brackets for extrusion, etc. ...Currently using this to hold my ramps on the underside of the second level of my 3 level lack enclosure.
thingiverse
I decided to mount a 40mm fan vertically next to my RAMPS board under the acrylic base of my rostock-mini to blow across the stepper drivers. This is a simple "L" bracket that lets you mount a 40mm fan vertically on a flat surface. It has 4 holes...
thingiverse
This mounts under the printer to cool the Ramps board. I used M3 bolts I believe they were 20mm long, but you may need longer depending on how deep your fan is. I didn't have to use nuts on the back because the bolts threaded right into the...
thingiverse
Its just nice mount the RAMP and Arduino board into my kossel mini using 2020 aluminium frame. ...Ini untuk meletakan ramp board dan arduino pada kossel mini atau proyek lain menggunakan aluminium 2020
thingiverse
Full enclosure for Ramps 1.4 board and my first Fusion 360 project. Edit: new rear panel added. Edit: a lid with fan added. ... Edit: a version with nuts and bolts added.
thingiverse
120mm fan mount for the tevo tarantula ramps "enclosure". ... Nothing special required to print.
thingiverse
Original Sketchup + OBJ File Included in addition to the file STL, so that any modifications of this model goes smoothly Therefor i have not printed it my self and im providing it as is to anyone of interest in using the case by mo78 for your ramps...
thingiverse
This is a simple case for HE3D Ramps plus board.
cults3d
This is a simple case for HE3D Ramps plus board.
thingiverse
Another contribution to the RAMPS box design collection. This is a simple open top box that fits the Mega/Ramps combo. Additional ventilation is through bottom slits and side holes. There is a side-hole for the reset button. The tabs are designed...
thingiverse
This cover for Sunhokey prusa i3 or other clone printer use 80mm fan, ramp 1.2 or 1.4 as long the screw hole is same, if not its up to you to modified it ^_^ Add hinge for easy open and closed front cover
thingiverse
This is my variable Fan holder for my MendelMax. I needed more flexibility because the wires are in the way of many other holders I could find - so I made a variable one. It holds a 80mm fan, you may need to drill the holes for the fan a little...