rav4 phone holder 3d models

Simple design for Rav4 Phone holder.

... There is a new version at: https://cults3d.com/en/3d-model/various/2017-rav4-cell-phone-holder-or-as-a-stand-alone-iphone-holder The update of THAT item is #32 that I included here but should I make any further changes please use the other project.

Just as the remix stated, this is a phone mount for the 2016 Rav4. My phone used the QI charging therefore I can't put anything on the back of my phone. I added hooked on the design to make it universal. ... Simply mirror the opposite side when...

The original was a simple and effective design, but I found the viewing angle to be better with the phone angled toward the driver at 22.5-degrees. This also increases volume knob accessibility. It causes the phone to lean left a bit though, so I...

A bracket to hold a mobile phone with a [PopSocket](https://www.popsockets.com/) for a Toyota Rav4 (Designed specifically for 2016 model). The bracket clips to the dashboard directly above the steering wheel, allowing you to more easily see and use...

This cell phone holder works great on a desktop or in my Rav4 as it is more cat proof as it is more stable than most holders. This was made for my IPhone 11 with a thicker Otterbox case with a Pop-cap attached. I made it wider and longer for wider...

Toyota Rav4 2014+ Dash phone mount holder. Included mount holder for iPhone 12 Pro with a not super thick case. ... You can easily design your own mount by taking into account the mounter clip dimensions

This is a simple phone holder for a 2010 Rav4. It fits in the small pocket right next to the e-brake and holds your phone conveniently next to the aux plug. ... It is intended for an iPhone 6 in a low profile case.

A phone holder designed for the Toyota Rav4 III beverage container. It houses a large phone of the size of the iPhone X, 11, 12, 13 in the MAX version. ...Smaller phones will of course also fit :)Additional small compartment for small...

Made to hold a phone in a 2018 rav4. Prints in 4 parts, no supports needed. With a hole at the bottom for charger to be able to go through. ...Glue bottom shaft to base plate and top part swivels without hitting the shifter or blocking cupholders.

I wanted to put a phone mount behind my steering wheel for navigation on my old 1996 Toyota Rav4.  I have an iPhone 13 Pro that I use on my commutes on the interstate to/from work.  I wanted more of a “heads up” display that let me drive...

I tested many phone holders for my Toyota RAV4, and finally decided to make a custom one. Magnetic car mounts are not compatible with wireless chargers (because of the metal plate you need to fix to the phone). The rest are bulky and hard to...

I tested many phone holders for my Toyota RAV4, and finally decided to make a custom one. Magnetic car mounts are not compatible with wireless chargers (because of the metal plate you need to fix to the phone). The rest are bulky and hard to...

Print it as it is, with 6-7walls (like 100% infill, but much faster) It will be "mounted" on top of the climate control. ... Can be attached and detached very easily.

Remix of youkai's Toyota Rav4 Dashboard Phone Holder. ...I printed this in PLA but I'd suggest ABS because PLA melts in the sun.

... ------------------------------------------------------------ Hello, Here is a phone (or else) holder for Toyota RAV 4! Designed to fit on a 2002 RAV4 1 Phase 2. ... Seems to be suitable for RAV4.1 and RAV4.2 To be tested for more recent models ...

There are two cup holders in the front, but if you use one with a phone cup holder (and there are two in the Rav4) one rider is holding his/her cup. There is a shallow tray in the front of the counsel, just under the dash. Our efforts to keep a...

Scangauge Rav4 Holder

This is a cellphone holder for a 1995 Toyota rav4, it's really sturdy. You'll need an old cellphone holder to take the cellphone holder mechanism. I used this old baseus, the socket uses a 17mm ball, it's attached using a 4x25mm screw. If you need...

rav4

ipad_holder_for_Toyota_rav4 Instructions Print with support.

Its a cellphone holder for a Samsung S10e (with case) for a 2010 Rav4. May work for other vehicle years or cellphones also (mileage may vary). The chances you need this design are 0%, but, in case you do, here it is. May also work with with other...

I really liked youkai's original design, but it mounted the phone about 1cm too low for me. A couple minutes in TinkerCAD easily fixed that. ... Please see the original thing (https://www.thingiverse.com/thing:2839187) for the support arms.

If you are an owner of a newer Rav4 you have a silly triangle area next to the cup holder that does nothing but collect dirt and junk as nothing will fit in it until now. This is designed to be wide enough to fit most phones and thick enough for...

I got my Toyota Rav4 used and it only came with 1 of the cup holder spacers. ...The dealer wanted $50 for one so I found a better solution.

I lost the beverage sleeve for my RAV4 cup holder and got sick of having my travel coffee mug bounce around in the naked cup holder. So I created this beverage sleeve. ... It keeps a travel mug safe and is just the right size for a CamelBak eddy.

A change holder I designed for a '12 Rav4 Center console. I am not sure if all model years of this generation have the same center consoles. This Design allows change to be organised in the upper compartment of the RAV4's center console and keeps...

It's intended to replace a space filler (from not used position) in Toyota RAV4 (gen V: from 2019) cockpit. Maybe it fits to Toyota Venza 2020 (filler size: 22.2 x 22.2 mm) I use "3 Positions Toggle Switch T80-R with automatic reset" (I bought this...

This phone holder is made for the Toyota OEM 2 din adapter part number 86221-52050, fitted to Toyota Celica T23 an tested for iPhone 11 & 12 with a thin case. Also other phones with about 80mm in width should fit. I suggest using V2.5 if u live in a...

I printed in PLA - it's winter here now - will need to re-print in ABS or similar for hot weather. ... This hanger clips onto the passenger side coins/stuff holder.