rdq mach 3 3d models

I remixed this mount to be thin and fit the VTX better than other designs.

Video Walkthough: https://youtu.be/KiYO3CPqr0k ► VTX - Race Day Quads Mach 3: https://www.racedayquads.com/products/mach-3-vtx-25-200-600-1000mw-2-6s-5-8ghz-video-transmitter?variant=17876578009201 ► Batteries - Emax 450mah HV 2 Required:...

30x30 mount to hold a RDQ mach 1, 2, or 3 vtx and a FrSky reciever.

Needed a canopy to totally enclose my RDQ Mach 1 build. Full protection and aero was the goal, so this thing came out. Thing I liked the most was the extra space above the stack. Acts as a shock-absorber during high impact, and allows good air flow.

Shark fin for RDQ Mach 1 frame for easy turtleing.

This is a mount for the RDQ Mach 1 frame for a regular Runcam Swift camera (not mini, or micro) or equivalent.

Allows mounting of Runcam Swift Micro on to the RDQ Mach 1 frame. ...This mount is designed to allow any camera angles without sticking the camera out too far.

Video Transmitter mount for the Mach 1 VTX made by Race Day Quads. ...Designed to be placed in the FC stack. VTX can be found here: https://www.racedayquads.com/products/mach-1-video-transmitter-vtx-25-200-600mw-by-rdq

Session mount for RDQ Mach 1 5" quad with 25 degree tilt Will require a lot of cleanup Best if printed with front face of the mount down (115 degree rotation about the X axis, then lay the face flat on print bed) Meant to be printed in TPU or other...

Video Transmitter mount for the Mach 2 VTX made by Race Day Quads. Designed to be placed in the FC stack. Slimmer version allows for tighter builds. You should print with supports. ...

This is a case that can hold a Mach 1 VTX by Race Day Quads. Good to hold it snugly against the frame, top plate, bottom plate, wherever. ... Cheers!

RDQ Mach1 quad battery mounting plate. Allows for leads for XT60 to protrude through the bottom. Also utilizes existing bottom-plate screws to mount with (just need longer hardware). Strap for battery goes between it and the frame. I add...

Mount your Mach 2 VTX under your stack. Spacers to give plenty of air space and supports FC with SD card slot on bottom. Just put your rubber standoffs on top and use an m3 screw to mate. ...No zip ties necessary, firm grip if printed in TPU My...

Mount your Mach 2 VTX under your stack. Spacers to give plenty of air space and supports FC with SD card slot on bottom. Just put your rubber standoffs on top and use an m3 screw to mate. ...No zip ties necessary, firm grip if printed in TPU My...

Scale TOP PART up by 3% for decently snug fit, or 2% for very snug fit. Better is 3% Three piece mount. Can use without fin or cam mount for reinforcement, with gopro 7 cam mount, or with just fin for turtle mode/better aerodynam The objective...

Session mount for RDQ Mach 1 5" quad with 35 degree tilt Will require a lot of cleanup Best if printed with front face of the mount down (115 degree rotation about the X axis, then lay the face flat on print bed) Meant to be printed in TPU or other...

25 degree GoPro Session Mount and top plate for the RDQ Mach 1. You have to turn the top plate 180 on the Mach 1 but with this mount you can put your battery on top! Mount designed to hold 3mm antenna tubes for RX, battery strap, and Gopro session...

This is the bottom plate for RDQ Mach 1 battery on top freestyle setup. Designed to hold the TBS Unify Pro family of VTX's. Used with a linear antenna with ufl connector the antenna can be run out the rear. This bottom Plate is designed to use the...

Simple GoPro Hero 6/7 mount for the RDQ Mach1. ... Supports buildplate only.

This mount is for the Runcam Swift Micro for the Race Day Quads Mach 1 Multi GP Spec racing frame. Available in 45, 55, and radical 60 degree angles. Uses the front standoffs for mounting and requires no screws. Best mount to protect your camera. ... ...

Soft mount flight controller and 4 in 1 ESC holder for the Mach 1. Designed to hold the Betaflight FC and the Spedix 4 in 1 ESC. Holes are setup for 30.5 X 30.5 standard flight controller pattern so any flight controller and 4 in 1 ESC may be used...

Couple of Mods: - Rx holder (XSR - Eachine) - FPV and RX antenna protection - Cable/arm protector - Arm protector (thicker walls)

Hi. This is a variation to the design https://www.thingiverse.com/thing:2408080. ... Greetings.

Simple stand to hold a Mach 3 razor

Simple holder for Mach3 razor. ... If you happen to have the same metal cage for soap bottles and you happen to keep a mach 3 razor in the shower, this is the perfect holder for your grooming tool.

... both in the bathroom and for travel. However, the latest Mach 3 razor does not come with a caddy from the manufacturer. This project makes a suitable caddy. ... It holds both the razor and a cassette with five replacement blade cartridges.

This Thingiverse design template offers a handy solution for Gillette Mach 3 razor users who want to carry their razor safely and securely on the go. The take-along frame is specially designed to hold the razor in a compact and lightweight frame. It...

... a V shape, but was worried it would allow doo much wiggle. ... this was inspired by the combo frsky and mach 3 mount. https://www.thingiverse.com/thing:3833047 bottom side left open for heat sync attachment newer versions in the works. ...

This utilizes the same FPV antenna mount as before, but with an added wedge for a go pro session. I have not found a perfect way to print this, but I print it with the mount flat on the platform. ...This will require some nasty cleanup, but it works.

This is specifically for the unify pro pigtails but you may be able to modify it to accept different pigtails.