rev expansion hub 3d models

Designed by Team 247 REBOOT This is the REV Expansion Hub mount. It is designed to have both of the Expansion Hubs to be in a small space. It is double sided to hold both of the Expansion Hubs. You have Access to all ports and different ways of...

Designed by Team 247 REBOOT This is the REV Expansion Hub mount. It is designed to have both of the Expansion Hubs to be in a small space. It is double sided to hold both of the Expansion Hubs. You have Access to all ports and different ways of...

This is a part that is designed to vertically mount a Rev expansion hub onto tetrix or actobotics C channel. The main purpose of this design was to open up space on my team's robot, as we had mounted our expansion hub horizontally before, so that we...

This part is to help keep the wire in the REV Expansion Hub. It features a low-profile so it won't take up much space on the robot and it sits flush with the ground. ...It is lightweight and uses a zip tie to hold the USB connection in place.

Then slide some pan head bolts up through the bottom of the rev module, up through the relief model and secure it with nuts. Plug your USB in and wrap zip-ties around the plug. In some cases, the 90° will be too big to be held by the two slots right...

Our robotics team has two REV Expansion Hubs mounted vertically in parallel along the robot's central axis, mounted to two 15mm REV extrusions. This leaves a 30mm space between the hubs, which is just the right size for our REV 12v battery. The...

connects to rev expansion hubs together and has a side mount for actobotics

Right-angle USB cable support piece for a REV Robotics Expansion Hub. ...Made by FTC team 8103 Null Robotics.

A quick 3D printed battery holder and expansion hub mount our FTC robot.

A quick 3D printed battery holder and expansion hub mount our FTC robot. ...

Two type of USB Stress Relief Options, One over the top and small, while the other stretches the bottom of the board. Both use zipties. ...The bottom mount will be available soon.

This is a FTC REV Control Hub and Expansion Hub mount I remixed from TheEV. It holds the Control Hub and Expansion Hub on each side and has cutouts for the USB ports. There are holes properly spaced for GoBIlda holes. There are also holes to mount...

This is a rev expansion hub to actobotics plate adapter with a USB strain relief clip.

A vertical Rev expansion hub mount for 2 hubs with a strain relief clip. ... Note that the cord has to be run through the relief, then plugged into the hub.

This design was designed with the REV Expansion hub or REV control hub in mind. The brace comes in two parts. The bottom is designed to be attached to the body of the rev hub either with glue or double sided tape. It is designed to accept a hex...

The module houses the rev slim battery and mounts the rev expansion hubs on the sides. This is our second post to Thingiverse and we are eager to receive some feedback. The assembly is pretty simple just attach the slide to the c-channel and slide...

These mounts are made for the REV Robotics expansion hub and battery as well as a Moto G play for FTC robots. It doesn't matter which side each part goes on so long as the battery mount is in the middle. The phone mount is purposely made slightly...

These mounts are made for the REV Robotics expansion hub and battery as well as a Moto G play for FTC robots. It doesn't matter which side each part goes on so long as the battery mount is in the middle. ...The phone mount is purposely made slightly...

Mounts between two goBILDA 1121Series Low Side U-Channels and 2 REV expansion hubs. Holds 1 Motorola E5 phone and 1 REV 12V Slim Battery or similar sized batteries. Screws, kep nuts, gobilda channels, and expansion hub designs found on Onshape.

This is a part made to help hold the USB wire on a Rev Expansion hub or Control Hub which can be used in the FIRST Tech Challenge competition. Robots have lots of vibrations so holding the USB wire in place is crucial. With this part, a zip tie can...

Added REV Expansion Hubs, Battery, Phone MountDeleted Original Intake Frame

FTC expansion hub

This mount allows you to attach two REV hubs vertically and back to back.

A case to store your REV Robotics Driver Hub. ...Many customization parts are included, as well as a blank base and cover to customize yourself.

This case houses and protects the REV Drive Hub utilized in the First Robotics FTC competition. ...An opening has been added to expose the speaker and tabs added to lock the device in place.

This is the 3D-printable case for the [Expansion Hub Type-C Adapter](https://www.tindie.com/products/doubledip/expansion-hub-type-c-adapter/). ... Update 8/6/19: The top cover files have been updated to include more clearance on the Type-C end for...

Its a T-Frame for the REV Robotics Expantion Hub.

The REV Driver Hub's USB ports are not easily repairable. This model helps relieve some port strain by not allowing the cables to have wiggle room. I printed it vertically with the ports facing downwards. The mount is attached to the driver hub using...

Team 3954 Pink to the Future designed this protective Cover for the REV driver hub. Of course, all necessary connections/buttons are still accessible. There is a small gap (0,5mm) left free to adapt for printer inaccuracy. Because the cover is split...

We designed a simple cable strain relief part that sits on top of the REV module (can even be screwed into the REV module and it's Actobotix holder. Once there, cables can be be plugged into the REV module and then zip tied to the cable strain...