rev robotics 3d models

Roomba roller adapter for rev robotics 5mm hex axle.

This part allows you to hold a new Rev Robotics battery it also allows you to stack a rev robotics module on top of the battery.

15mm extruded aluminum created by REV Robotics designed specifically for use by FIRST teams.

Rotate Part Flat. ...This cap is 1/8 inches thick, and screws into the top of Rev's 15mm linear slides, using a 6/32 Screw. Tap 15mm slide first. Rev Robotics 15mm Slides: http://www.revrobotics.com/15mm-extrusion/

This model includes a shortened 3rd stage, as well as some (admittedly Janky) mating of the other slide.All credit goes to REV Robotics: http://www.revrobotics.com/ for the files, All I did was make an assembly for them, as I couldn't find one on...

A battery mount for REV Robotics batteries. U-shaped cutout allows for easy grabbing of battery while still securing it in place. ...The screw holes are designed for REV screws, but if you drill them out they can should be able to be used with Tetrix...

These are slides for Rev Robotics extruded 1" aluminum. These allow linear motion without having to use wheels and bearings. I printed mine with 4 walls and 50% infill. I posted a picture showing how it is almost completely solid. I printed them...

This is an approximation of the REV Robotics 15mm extrusion. It was created to support build activities of FIRST FTC Team #13599 Bruinbots for their 2018 season. The OpenSCAD file is attached for your use and improvement. There are pieces of the...

This is an approximation of the REV Robotics 15mm extrusion. It was created to support build activities of FIRST FTC Team #13599 Bruinbots for their 2018 season. The OpenSCAD file is attached for your use and improvement. ...There are pieces of the...

Rev Robotics Battery Holder

Cases to hold the new REV Robotics Level Shifter(s)

T-Gusset plate created by REV Robotics. ...Intended to be used on the REV Robotics 1" extruded aluminum.

This is a pulley cover we have designed to attach to the REV Robotics channel. ...Attached are the files to print just one, or sixteen covers.

... after having isses with the orignal design by ftc 5086. These are designed to fit around the 15mm Bearings from Rev Robotics Rev Robotics Pulley: http://www.revrobotics.com/rev-41-1368/ FTC 5086, CH Tutu Turtles: https://twitter.com/ftc5086?lang=en

Team 8778 - GridSkippers - designed this bearing as an alternative to the REV Robotics 15mm linear motion kit. 4 slides per stage is needed. ...Modeled after the 80/20 linear slide bearing.

Made these pulley covers to keep the string on the Pulleys for a FTC Lift They are for the pulleys sold for the REV robotics 15mm extrusions The tolerances are very tight, print on the highest setting possible They have a tab to keep them upright and...

These types of angle brackets were designed for connecting REV extrusions. These brackets are if you are trying to attach an extrusion to another extrusion. These parts are specifically designed for FTC (FIRST Tech Challenge) teams. ... Compatability:...

A rev sensor mount with actobotics hole pattern for mounting. ... Designed to reach an oddly positioned linear slide so that we did not break the string.

Dimension on this REV Robotics were adjusted after consulting the CEO of REV Robotics.

This is a cap to protect the end of REV Robotic's 15 mm extrusion.

This is a cap we designed to screw onto the end of the REV Robotics channel.

uses both 12 x 6 bearings (spool) and 12 x 8 bearings(motor) with adapters from rev robotics. ... Tetrix hubs and gear on the spool, rev robotics hex shaft and gear on the motor

This is a battery box designed for Rev Robotics' Slim battery for FTC. ... There is a Tetrix hole pattern.

A simple mount for a REV Robotics XT30 Power Distribution Block. ...This design works best with flexible filament but other materials should work as well

A Strain reliever for the REV Robotics Servo Power Module, since we have found that the servo wire connections came out quite frequently. The tines fit around the wires while holding the connection in place. ...Taller connections can use the higher up...

This is a case for the new rev robotics driver hub. All I/O is accessible. There are holes on the back to match those on the bottom of the driver hub. It is intended to be made out of TPU or other flex filament. ...The corners have been enlarged for...

This adds additional strain relief to a Rev Robotics power switch, required in FIRST FTC robots. In the past our team, FTC #12598, has had the lugs coming loose or breaking off, and this has also been an issue with other teams. Print with a brim...

I customized the Customizable Plate Bracket by mightynozzle for the [REV Robotics](http://www.revrobotics.com) build system that uses 1515 extrusion. I wanted my FTC robotics team to be able to create custom brackets quickly and easily since we have...

My original design fits the 1515 extrusion from Andymark perfectly but not the 1515 extrusion from REV Robotics - the channels are fractionally smaller. The "Linear Slider Simple" is the easy one to fit with scaling, but if the original version can...

End cap for REV extrusions to cover sharp edges. ...Only works with REV 15mm extrusions.