samsung freestyle ceiling mount 3d models

Ceiling mount for Samsung Freestyle Projector. ... Comes with optional clip to secure your expensive projector a little bit more.

Support for installing the Samsung Smart Freestyle Projector on walls and ceilings.

3D model of The Freestyle Samsung Green

3D model of The Freestyle Samsung Brown

3D model of The Freestyle Samsung Pink

3D model of The Freestyle Samsung

This is an adapter that can be attached to this model: https://www.thingiverse.com/thing:5539841 it can be attached diagonally on that adapter and you can tighten it to the pipe with the same screws

VTX holder for HDZero Freestyle VTX. ...This fits 30x30 mount pattern. HDZero_Freestyle_Mount_H2 has .25mm padding around VTX HDZero_Freestyle_Mount_H2_P4 has a 4.5mm padding around wiring harness ports.

Part for mounting a 9 mm buzzer / beeper on Emax Tinyhawk Freestyle.

Firefly cam mount for TH Freestyle, I will upload another with more uptilt later.

Part for mounting a 9 mm buzzer / beeper on Emax Tinyhawk Freestyle.

I created this to surface mount my freestyle vtx on my wing for better airflow. ...Mount it how you like, but I buried some standoffs in the foam with e6000 so that the vtx would be easily removeable for servicing.

Samsung The Freestyle Projector 3D model High Poly 4 Color product - Withe, Green, Pink end Beige Count Poly - 427308 Reference Product - https://www.samsung.com/br/projectors/the-freestyle/lsp3b-the-freestyle-sp-lsp3blaxzd/

Simple bed head stand for Samsung The Freestyle, feel free to adjust the dimensions on Tinkercad link as below: https://www.tinkercad.com/things/i0a8urG0D0H

This mount replaces the front two standoffs and the camera slides in from the top. The bottom of the mount protects the camera and the top is still protected by the frame. It is set for 20 degree uptilt. ... Printed with PLA on generic settings with...

... to hold the Emaxx nano polarized antenna. ... The video below shows how I upgraded the camera, VTX and antenna. https://youtu.be/5_DJMvW-GoI Check out my camera mount as well. ... https://www.thingiverse.com/thing:3851258 Print with two perimeters.

... 2 perimeters, 1.5mm height, if using a nozle smaller than .04 make sure to use 100% infill. I have an Emaxx Nano antenna mount as well: https://www.thingiverse.com/thing:3878308 See the video below for more information, https://youtu.be/5_DJMvW-GoI

**Buy The Frame Here: https://store.bicks.us/** **Print Settings:** Make sure to print out of TPU, and with the bottom part of mount flush against the bed. No support needed. I'd recommend 2-4 walls, and infill is best at 10% or higher on a 0.4mm...

simple ceiling mount bracket. I use 2 M4 screws and 2 nuts to attach the lamp holder and 2 wood screws to fix the holder to the ceiling. ...I used the soldering station to push the nuts on the printout

HDZero Freestyle 1w VTX mount for any fixed wing.

This is a simple wall mount for Prodigy Freestyle Scooter.

This is the ceiling mount for the universal bracket. I have not printed/tested this yet, so print at the risk of balence isses, or the bracket not fitting correctly. ...I would use a carabiner or other to hand.

Ceiling profile leveling jig compatible with Norgips ES 60 X 250. ... Wieszak plaski

This is a simple plant hook designed for my ceiling grown flower

Mount for firefly on amax freestyle 5-7 frame. Print in TPU. ... Work in progress.

Started with "HDzero - Freestyle Antenna Mount - Source One V3 by Bootdsc" then added a GPS mount to base of the mount.

This is replacement for 2 rear posts for Emax Tinyhawk2 Freestyle frame. ... It allows to mount Rush Cherry antenna at the end of the quad.

Added a Go pro mount 25 degres Tilt. ...If the printed tpu, 100 pourcent, was very strong! I just adjuste this gopro mount for the amax Freestyle 5 and may be 5E.

XT30 mount for Emax TinyHawk Freestyle. ...TPU, Soak model in boiling water for 30 seconds to make it easier for XT30 to fit as it is a very snug fit.

always liked the idea of having a SQ11 or tiny camera on the tinyhawk freestyle, but didnt know how to mount it, this was a simple idea that actually works pretty well, it uses the strap to hold down the camera via a "surfboard or snowboard" type...