sanding pla 3d models
212307 3d models found related to sanding pla.thingiverse
I have been 3D printing for about 4 years now and I have always struggled to find an easy way to smooth PLA filament. After mistakenly spraying Polyurethane on my 3D model, I decided to see if it was thick enough and would dry fast enough to fill in...
cults3d
I have been 3D printing for about 4 years now and I have always struggled to find an easy way to smooth PLA filament. After mistakenly spraying Polyurethane on my 3D model, I decided to see if it was thick enough and would dry fast enough to fill in...
thingiverse
After printing WorkShopBob's Sanding Sticks I wanted a water tank I could use for wet sanding PLA. I designed it with an insert that has holes and ridges. The idea was for the ridges to knock off debris and fall through the holes. ...I have no idea if...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=101307 Instructions Using the following options: build_plate_manual_y = 100 build_plate_manual_x = 100 build_plate_selector = 0 KeyChain_9 = KeyChain_8 = KeyChain_7 = KeyChain_6 = KeyChain_5 =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=101307 Instructions Using the following options: build_plate_manual_y = 100 build_plate_manual_x = 100 number_of_keychains = 1 KeyChain_9 = KeyChain_8 = KeyChain_7 = KeyChain_6 = KeyChain_5 =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=175150 Instructions Using the following options: font = write/orbitron.dxf line_10 = letter_spacing = 1 line_spacing = 2 slitlength = 12 slitwidth = 4 text_style = -80 fontsize = 8...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: bar_shift = 7 lug_width = 0 ruler_unit = 10 font_with_style = Advent Pro (Bold) bar_length_trim = 12 bar_color = Khaki bar_thickness = 2.4...
cults3d
Because the drill and the thing moves enough air / blows against the target, I didn't had problems to dry-sand PLA. https://youtu.be/Hf2k6ma2GJU WARNING: I tried it for some minutes and low sped with a Dremel and killed the Dremel with it. Either...
thingiverse
Because the drill and the thing moves enough air / blows against the target, I didn't had problems to dry-sand PLA. https://youtu.be/Hf2k6ma2GJU WARNING: I tried it for some minutes and low sped with a Dremel and killed the Dremel with it. ...So...
prusaprinters
Combined with a drill and it really saves some work and made sanding much easier. Because the drill and the thing moves enough air / blows against the target, I didn't had problems to dry-sand PLA. WARNING: I tried it for some minutes and low...
thingiverse
Identified the need for sanding the PLA pieces, then I made this compatible 3D model with automatic screwdrivers. Print, glue the sandpaper with a double-sided tape and go sand! ... Resize 6.6 in repetier software to have a 0.6 mm plug-in.
cults3d
... block (80mm x 15mm) easy to print. ... you need a 19,5 cm strip of sandpaper, and nothing else! printing in pla or abs. Sanding block (80mm x 15mm) easy to print. you need a 19.5 cm strip of sandpaper and nothing else! ... printing in pla or abs.
cults3d
Sanding block (73mm x 15mm) easy to print. you need a 6-inch strip of sandpaper, and nothing else! printing in pla or abs. Sanding block easy to print. you need a six-inch strip of sandpaper and nothing else! ... printing in pla or abs.
cults3d
... You just have to place a special adhesive support, then standard sanding disks. The block is design to be easily used by a human hand ;-) and you'll be able to place your hand close to the surface to be sanded. ... Thanks to all for your support!
thingiverse
Customized version of https://www.thingiverse.com/thing:2768920 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2768920
thingiverse
This is sandpaper holder for sanding miniatures. It is held together with #6 self-tapping screws. ...I have only printed this in PLA.
thingiverse
You need to print 3 parts: sanding_wedge sanding_wedge_clamp screw_nut_holder I used an M6 screw and nut to clamp the sandpaper down. The screw and nut are glued in place. ... I used PLA but ABS would be better.
thingiverse
Sanding block for belt sander belt 75 x 533 mm Print with PLA/ PETG Mine are PETG You also need a 6 x 75mm screw and a 6mm Tee Nut
prusaprinters
Required a quick and easy tool to assist with sanding some of my cosplay props. Designed this in Fusion 360, and takes roughly 3 hours to print. Print instructionsPrint at 0.2mm with at least 20% infill. ...PLA works fine.