sata3 to usb 3d models
2150004 3d models found related to sata3 to usb.cults3d
This is a case for the Hasu USB to USB Controller Converter from 1upkeyboards
thingiverse
This is a case for the Hasu USB to USB Controller Converter from 1upkeyboards
grabcad
this is a pcie 1x to usb riser.there are many slightly different brands and versions
thingiverse
A simple usb to dupont wire connector for those who need to convert their usb charger into a little power supply. ... UPDATE: Added + and - signs so you know where to put the right wire.
thingiverse
Case for USB to TTL Converter. ... U need: - FT232RL FTDI Mini USB naar TTL Seriële UART Adapter - 15 x 10 mm Boot Rocker Switch - 3 mm led - 150 Ohm resistor - Some wire Use Dupont or Pogo Pins
cults3d
simple way to connect your usb devices to your hose. ... https://www.tiktok.com/@maddy_deee/video/7101287768654875909?is_copy_url=1&is_from_webapp=v1
thingiverse
Here a tiny case for a USB to TTL (FTDI) adapter. ... The case version 11 is equipped with a mounting rail for Anycubic Vyper!
thingiverse
I've designed this Dual-USB to RJ45 adapter for connecting two USB ports with my 3D-Printer (1x printer + 1x webcam) using only one patchcable (RJ45 Keystone-Module on the printer). For this cable you need two USB-A plugs like these:...
cults3d
I've designed this Dual-USB to RJ45 adapter for connecting two USB ports with my 3D-Printer (1x printer + 1x webcam) using only one patchcable (RJ45 Keystone-Module on the printer). For this cable you need two USB-A plugs like these:...
thingiverse
... ...Used a 5v 3amp USB port and a XT60 Female Plug to design the case. ... Print Settings Rafts: No Supports: No
thingiverse
I wanted this instead of the more popular USB-to-serial dongles because the IO is logic level (3.3V) instead of +/-15V, and there's no reason to use a bulky DB-9 connector. Instructions This board is designed to be easily fabricated on 1 layer PCB...
thingiverse
ISA to USB bracket designed by YouTuber RetroTech Chris. Design feedback is welcome, and please let me know if you have any issues with the print. ... To connect the bracket to the card, you can use "floppy drive screws" (or self tapping screws if you...
grabcad
A ubiquitous benchtop accessory for those of us still using old, or homemade, dev tools... ... Converts usb to old, 8bit serial comms on a 9 pin, sub-d connector.Thanks to Alex K for the 9-pin sub-D connector model.
thingiverse
Coque pour un de mes projets d'adaptation d'une manette de N46 vers Usb prend un port manette officiel Player 1 et 2 (surement les 3 et 4 mais en symétrique) avec Arduino pro mini. Projet ici: http://diolum.free.fr/projets/n64usb/n64USB.html ...
thingiverse
This is a solder-less way to have usb to 4 dupont wires for breadboard and other applications. ... it uses an usb plug, exactly this https://www.alibaba.com/product-detail/DIY-USB-2-0-A-Male_62030825424.html so it wont damage the usb port at all.
thingiverse
I bought a USB to USB ground isolator that doesn't have a housing. Very handy item at times. Needed a case. ... https://www.aliexpress.com/af/ADUM3160-isolation.html
thingiverse
I remixed spavis' "USB C to MicroUSB keychain dongle holder" to have a bigger ring as mine broke. ...Just a quick edit I did in OpenSCAD between deaths and rounds in Overwatch.
thingiverse
Designed this to cover the USB to USB 180-degree connector due to it being slightly unsightly, especially when used outside of a case. The connector mentioned is this one: https://geekworm.com/products/usb3-0-connector Although others have...
thingiverse
I bought a 3 pack of USB-C to USB-A dongles for my new MacBook Air, and soon realized that they would be very easy to lose. I decided to make a small holder for it that could be secured to something. The hole in the back is used to push the dongle...
thingiverse
V2: The USB-C portion of the adaptor was too short to reach her Ipad (since it had a case). Therefore i cut the originals case with a dremel tool (carefully), put some hot glue to cover the electronics, and then slipped on this protective case that...
grabcad
This print is to hold a USB adapter (specifically this: https://www.amazon.com/gp/product/B072J5B3BR/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1)included is the STL and the Solidworks part file. ...There is a hold for a 4-40 set screw in the top if...
thingiverse
Case for a Micro-USB to type-C adapter. Keeps your connector dust and dirt free. ... Outer dimensions case: 16.2 x 10 x 25.4mm (Case fits adapter ±:11.5 x 4.7 x 22.8mm) Both parts clamp together, but can can come loose with little force, which is...
prusaprinters
I made this USB to USB-C cover for wife. V1: The adaptor that we bought (link below) did not have something to attach it to a key chain, this tight fit worked great. V2: The USB-C portion of the adaptor was too short to reach her Ipad (since it had a...
prusaprinters
I bought a 3 pack of USB-C to USB-A dongles for my new MacBook Air, and soon realized that they would be very easy to lose. I decided to make a small holder for it that could be secured to something. The hole in the back is used to push the dongle...