scale rc cars 3d models
445810 3d models found related to scale rc cars.thingiverse
This is a little collection of gadget for 1/10 scale rc cars
thingiverse
Tires for RC cars, compatible with 3D Sets [3D-printed RC cars](https://www.3dsets.com/). Print using TPU. Mirror the model to print full sets of four tires. Tires have 45mm inner diameter for a tight fit, and therefore can't be printed with semiflex...
prusaprinters
Tires for RC cars, compatible with 3D Sets 3D-printed RC cars (https://www.3dsets.com/). Print using TPU. Mirror the model to print full sets of four tires. Tires have 45mm inner diameter for a tight fit, and therefore can't be printed with semiflex...
cults3d
side mirror for 1/10 scale rc cars, classic style (60-80ies)
thingiverse
... a near-scale replica of a roof rack and horn I had on my VW Mk1 Rabbit. I made it to fit my 1:12 scale Mk1 Golf. Will probably fit other 1:12 scale RC cars also. ... The rack is held to the roof, and the horn to the rack, with sticky back velcro.
thingiverse
This is a 3D-Printed AirBox / Air Filter for "Big Scale" RC-Cars 1/5 1/6. It is specifically designed for easy printing with no or very little support (see "Print Settings" for details). This AirBox requires around 5h to print and weights around...
thingiverse
i made this for my ECX barrage and it looks quite nice and it is a good scale accessory. it goes well on the back of a ute body. ...i don't have the best 3D printer so the quality isn't great,
thingiverse
This is a camber guide for RC cars, 1/10 scale, set to 1 degree. It's non-adjustable, but 1 degree is the camber setting RC racers use most of the time, so it's useful. It has a cutout for wheel-nut clearance as well. I've printed this in ABS on a...
thingiverse
3D printable shocks for RC cars. Specifically 1/10 cars with ~81 mm front and ~91 mm rear shock lengths center to center. These shocks fit the MKUltra buggy perfectly: https://cults3d.com/en/various/mkultra-3d-printable-1-10-4wd-buggy The PDF...
cults3d
3D printable shocks for RC cars. Specifically 1/10 cars with ~81 mm front and ~91 mm rear shock lengths center to center. These shocks fit the MKUltra buggy perfectly:https://cults3d.com/en/various/mkultra-3d-printable-1-10-4wd-buggy The zip file...
thingiverse
Shock rebuild stand for 1/10 scale vehicles. Designed to hold the shock bodies while the oil settles, and keep things neat during this messy job. Designed for standard 12mm shocks, like Team Associated B6/B6D, B64/B64D, Losi 22 etc. The holes are...
thingiverse
Replace part for 1/10 scale rc car Special design for SLA printer for best result
thingiverse
Side mirror for 1:10th scale RC cars (touring/street cars). ... Right mirror only, you have to mirror it yourself.
thingiverse
A 1/10th scale RC car camber gauge. ... 0 degree location is marked, reads up to 7 degrees of camber in 1 degree increments (each line is 1 degree)
thingiverse
I printed them 100% and changed the filament while printing.
thingiverse
A set of tie rods for the WLtoys 1/28 rc cars. My rear wheel was a little angled from the factory, so I designed these to help me adjust it. They are 13.3mm, 13.8mm, 14.3mm, and 14.8mm. ...The sizes are marked with numbers on the arms themselves as...
cults3d
A set of tie rods for the WLtoys 1/28 rc cars. My rear wheel was a little angled from the factory, so I designed these to help me adjust it. They are 13.3mm, 13.8mm, 14.3mm, and 14.8mm. ...The sizes are marked with numbers on the arms themselves as...
thingiverse
Not recommended for "bashing" or extremely rough driving/jumping, these are best suited for scale crawlers/trail trucks, on road cars, drift cars, ect. An M3x12mm bolt and nut are required to secure the top piece to the lower piece. the mount can be...
myminifactory
Not recommended for "bashing" or extremely rough driving/jumping, these are best suited for scale crawlers/trail trucks, on road cars, drift cars, ect. An M3x12mm bolt and nut are required to secure the top piece to the lower piece. ...the mount can be...
cults3d
Parts list: WLToys 1/28 RC car with drift wheels/tires Standard towerpro style 9g servo Eachine ATX03 RunCam Nano Small 1s battery for video system The lights are all 3mm LEDs, 6 in the rear and 4 in the front. Thanks for looking! *UPDATE 11/26/18...
myminifactory
One piece RC body mount. Fits 15mm circular magnet and 5.5mm to 6mm posts. ...Easy to print.
thingiverse
One piece RC body mount. Fits 15mm circular magnet and 5.5mm to 6mm posts. Easy to print. ...
myminifactory
Parts list: WLToys 1/28 RC car with drift wheels/tiresStandard towerpro style 9g servoEachine ATX03RunCam NanoSmall 1s battery for video system***The lights (optional) are all 3mm LEDs, 6 in the rear and 4 in the front. I control mine with an...
grabcad
One of my first projects in Solidworks, Tamiya TT-01 1/10 scale RC car
grabcad
This is a SCX10 1/10 scale rc car rear axle. ...Its not an assembly, it's just a model for the measurement and stuffs.
thingiverse
This is a scale model of a set of v8 velocity stacks which could be glued to the bonnet of an RC car. ... UPDATE: Smoother higher res STL now uploaded too, for a less polygonal finish Enjoy!
thingiverse
For new owners of drift rc cars that crash alot... ..."Me"