screwdriver holder harbor freight 3d models
341853 3d models found related to screwdriver holder harbor freight.thingiverse
a basic screwdriver holder to hold the cheap @$$ blue multi-screwdriver from the good ol harbor freight. printed with the flat side down. designed to be affixed with a 3m command strip. ... harbor freight screwdrivers like this have really poor...
thingiverse
Customized version of https://www.thingiverse.com/thing:2725510 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2725510
thingiverse
Harbor Freight Pittsburgh 6 pc Screwdriver Set Wall Mount for item #47770: http://www.harborfreight.com/6-piece-screwdriver-set-47770.html
thingiverse
Ratcheting Screwdriver Set 26pc (Pittsburgh - Harbor Freight) Holder for Gridfinity. Build on a 4x3 Base. Approx 143g Material needed. ...Extra slots for additional bits, and a small parts bin has been added.
thingiverse
I needed a decent holder for my precision screwdriver and hadn't seen anyone make this yet, so I made one myself. ... Remixed from Zack Freedman's Gridfinity templates and from another thingiverse thing: https://www.thingiverse.com/thing:3393817
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=537516 Instructions Using the following options: closed_bottom = 0.0 holder_x_count = 6 holder_y_count = 1 taper_ratio = 1.0 holder_x_size = 13 corner_radius = 30 holder_height = 15...
thingiverse
https://www.thingiverse.com/thing:3599298 This is a screwdriver and screwdriver accessory holder for all the screwdrivers and screwdriver accessories in the Harbor Freight 130 piece toolkit with the exception of the extension and micro drivers. ...
thingiverse
Replacement slide on 3/8 drive socket holder insert for the Harbor Freight magnet organizer. ...Friction fit rather than ball bearing snap but it works fine.
thingiverse
Based on Harbor Freight Clamp Holder by Fillitup309 but modified to print as a single piece with no supports. I barely made any changes at all. ---- Organize your Harbor Freight clamps. 4, 6, or 8 clamp holder (6 should be short enough to print on...
thingiverse
This is a holder screws to the wall to fit a small flashlight from harbor freight (those free ones with the coupon). ... We used it for placing emergency flashlights near our entrances and on our powder coating setup.
cults3d
But the Harbor Freight glove box doesn't fit very well into the Harbor Freight glove dispenser... Go team... Problem solved. ... This glove holder has three countersunk mounting holes and it's even got "GLOVES" printed right into the front of it in...
thingiverse
A stand for a Harbor Freight Multimeter. ... I added some pockets for magnets to the stand.
thingiverse
But the Harbor Freight glove box doesn't fit very well into the Harbor Freight glove dispenser... Go team... Problem solved. This glove holder has three countersunk mounting holes and it's even got "GLOVES" printed right into the front of it in...
thingiverse
I designed this Harbor Freight flashlight holder so when I change tools on my machine at work, I can see in the dark tight areas. This holder uses 5mm x 5mm x 3mm thick magnets. ... I have also included the Fusion 360 file so anyone can change it...
myminifactory
I designed this Harbor Freight flashlight holder so when I change tools on my machine at work, I can see in the dark tight areas. This holder uses 5mm x 5mm x 3mm thick magnets. ... I have also included the Fusion 360 file so anyone can change it...
thingiverse
... it prints so I made this to fit my printers 2020 frame. ...Its a simple harbor freight soft copper brush that I cut to make it fit inside of the holder.Its a static fit. ...have used it for like 6 months now with out issues at all on my 400mm bed.
thingiverse
I modified an existing Fluke Meter Holder design to accommodate my Harbor Freight Multimeter. I did some trimming and resizing in Tinkercad and came up with a stand for my meter that sits on my bench and holds the meter making it easier to use and...
thingiverse
Organize your Harbor Freight clamps. 4, 6, or 8 clamp holder (6 should be short enough to print on most printer beds) The clamps are designed so that the clamps are angle to the left (insert clamps from the left) because I'm left-handed. You will...
thingiverse
This is an easy mount for wall mounting disposable gloves from Harbor Freight. I used a level to draw a baseline, then measured the box and drew another line with a level to keep it square while mounting. quick, easy, functional!!! These...
thingiverse
This is designed for those cheap flash lights from harbor freight but will probably work with many other brands. the holes are 28mm diameter. One design has 4mm holes for mounting with screws and the other does not for mounting with tape. I printed...
prusaprinters
... items. ...I don't remember what the print settings were but it was printed in PLA Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 200 Infill: 20 Filament: Tianse PLA Yellow Category: Tool Holders & Boxes
thingiverse
Caddy for Harbor Freight's Pittsburgh "34 Pc. Precision Screwdriver" set that comes with a flexible extension. ...
thingiverse
Star Bit Screwdriver Set tray: Designed to fit Harbor Freight Pittsburg brand Star Bit Screwdriver Set. ... Star Bit Screwdriver Set, 6 Piece SKU: 94757 Tray measurements: Compact (untested): 145mm wide, 220mm deep, 22mm tall Wide: 170m wide, 220mm...
thingiverse
It's provided as a starting point for anyone else that is interested in hacking their Harbor Freight 4.8V Screwdriver. In the current iteration,the two ribs going toward the back shell (closer to the motor) are a bit too thin and possibly about...
pinshape
It's provided as a starting point for anyone else that is interested in hacking their Harbor Freight 4.8V Screwdriver. In the current iteration,the two ribs going toward the back shell (closer to the motor) are a bit too thin and possibly about...
thingiverse
Harbor Freight Pittsburgh 8 Piece Pin Punch holder for 2 sets of punches.
thingiverse
Made a pick holder to hold my pick set I purchased from Harbor Freight, it will hold 9 picks.
thingiverse
This is a bit holder for the Harbor Freight socket hex bit 9 piece set. ...Very handy for my workbench .