self adhesive cable tie mounts 3d models
473269 3d models found related to self adhesive cable tie mounts.thingiverse
You can buy self adhesive zip tie mounts for $7 - 100 pieces, but save a few cents by making your own. The mount measures roughly 1/2" (12.7mm) x 3/4" (19.05mm) x .150" (3.81mm) tall. ...I made the width of the openings (.220") large enough that 3/16"...
grabcad
20 mm SELF ADHESIVE CABLE WIRE ZIP TIE MOUNTS PART NO. ...70478https://bit.ly/2VPggWx
grabcad
20 mm Self Adhesive Cable Wire Zip Tie Mounts Part No. ...70478https://bit.ly/2VPggWx
thingiverse
I made the first clip 25mm square as to fit my roll of double sided tape which is 50mm wide, it will also take up to a 5mm wide zip tie through it. the second file is just a scaled down version of the first one. ...down to 20mm/
cults3d
After seeing a Tiktok video I have a cool item to store his cables. So I modeled it it is simple to print in TPU. ... In my case it was printed in TPU 70D from Nanovia
thingiverse
Designed this minimalistic cable tie mount, to be used with double sided adhesive. Goal was for it to be as simple as possible while being sturdy and print almost without retractions. ... Fits 100mm (4") tie, and uses a 20x20mm piece of tape.
thingiverse
No support cable clip. ...VHB on the back and a zip tie around it. Curve maintains positive inward pressure on cables. ... Used on my vehicle rooftop solar project and has found its way into a few others since.
grabcad
This is a close approximation of a self adhesive cord clip - Panduit ACC62 series.
thingiverse
Can be mounted on any surface with double-sided adhesive tape. ...Different radius to hold different cables. Easily fasten the cables with cable ties.
prusaprinters
Simple design, fast printing and hardly any material used.No more buying large packs at the DIY store even though you only need a few.In this case, you can also simply remove the cable again.Depending on the cable thickness, the model can also be...
thingiverse
If it gets delisted, it disappears from your collection. Cable tie mount: 20mm x 20mm x 6.6mm Cable tie openings are 5mm x 2.2mm. Top hole is 5mm x 5mm. **Print Settings** Printed in PLA, .2mm layer height, 2 shells. ...Use adhesive tape on the back.
thingiverse
__Apologies as I am not reposting to keep it in the current/newest list.__ Cable tie mount: 20mm x 20mm x 6.6mm Cable tie openings are 5mm x 2.2mm. Top hole is 5mm x 5mm. **Print Settings** Printed in PLA, .2mm layer height, 2 shells. ...Use adhesive...
thingiverse
... other brands, too. A 15x15mm flap gives you access to the grip part of the adhesive strip, so that you can remove it without any damage when it is no longer needed. Project homepage: https://hattedsquirrel.net/projects/adhesive-strip-to-cable-tie/
thingiverse
I needed some Cable Tie Mounts (https://tinyurl.com/h35l4tw) and thought it would be cool to 3D prints some. I used SketchUp and created my own version. ...Apply some double sided sticky tape and you are all set.
thingiverse
Self-adhesive plastic motor mount for miniature DC motors. These are often used in schools with Crumble / MicroBit microcontrollers for robotics/buggies and cost a small fortune. ... These are just as good, print in about 25 minutes and cost fractions...
thingiverse
Zip tie mount for use with adhesives like hot glue etc. ...Fits 3mm x 6mm zip ties.
grabcad
Simple model of a cable tie with saddle and self tapping screw
thingiverse
Cable tie mounts for 20x20 aluminum extrusion rails. Five different versions: 45, 90, 135 and 180 to the extrusion, and a round version that has no spline so it can be set at any angle. Because the round version has no spline, it can also be used...
thingiverse
This is a simple mount to screw down and attach a cable tie to should work with most screws this model has a through hole of 5.5mm so ensure your screws thread diameter is less than that and the head of the screw measures bigger than 5.5mm this is...
thingiverse
This is a simple Cable Clip. ...You can use it with M3 screws or similar but you can also mount it with self-adhesive tape. ...The inner diameter is about 6mm.
prusaprinters
This is a simple Cable Clip. ...You can use it with M3 screws or similar but you can also mount it with self-adhesive tape. ...The inner diameter is about 6mm.</p> <p>01-12-2020: CLIP WITH LARGER DIAMETER ADDED</p> Category: Electronics
cults3d
Self-adhesive kitchen shelf for kitchen roll. It needs double-sided tape. Can be put in multiple positions to suit the consumer. ... Update: It has been reinforced to improve functionality.
prusaprinters
Simple cable tie mounts that you would apply double stick adhesive tape to. Dimensions are: 19mm x 19mm Fits up to 4mm cable ties. You could scale this up. Im am yet to print these but they are modelled off a physical mount i have at home. I plan to...
thingiverse
If pictures or STL are missing/broken please check the github repo: https://github.com/TylorKing/3D ___________________________________________________________________________________________________________________________________________________...
thingiverse
this thing will make u easier to manage your cabling on your 3D printer that using 2020 aluminium profile... PS: better to heat the clip hook before inserting to the 2020 profile gap... ...it's will make the clip easier to insert and wouldn't break...
cults3d
this thing will make u easier to manage your cabling on your 3D printer that using 2020 aluminium profile... PS: better to heat the clip hook before inserting to the 2020 profile gap... ...it's will make the clip easier to insert and wouldn't break...