sharpie magnet 3d models
59092 3d models found related to sharpie magnet.prusaprinters
Hi! you will find here an evolution of the cap's Sharpie!Two magnets are inside this new cap to put your favorite pen everywhere!Dimensions of the magnets :20x6x2 mmD8x3,2 mm
thingiverse
Needed a magnetic Sharpie holder. These are 6mm x 2.5mm magnets. The hole is very tight so that the magnet stays put in there and it doesn't get stuck to the fridge, etc. This will hold any regular sharpie, I am using it for smaller dry-erase...
thingiverse
I designed these magnetic clips to hold permanent sharpie and large sharpies as well as dry erase markers of the EXPO brand, if you purchase these magnets on Amazon they will fit perfectly inside with just a little pressure, no glue required (I...
thingiverse
Parts: PLA filament A 1"x1/2"x1/8" magnet with countersunk holes (https://www.kjmagnetics.com/proddetail.asp?prod=BX082CS-S&cat=19) \#6-32 heat set inserts (https://www.mcmaster.com/94459A280/) \#6-32 x 1/4" countersunk screws...
thingiverse
I used 10mm diameter magnets extracted from a Dollar store Cellphone magnetic car vent mount and popped them into the base of the device and after a few iterations to get the thicknesses right to maximize the magnets pull and the strength of the...
prusaprinters
I solved that problem by creating the Be The Change Kitchen Tape & Sharpie Fridge Magnet. As in, Be The Change you want to see in the kitchen. Put the F#$%KING TAPE AND MARKER BACK.With a strong enough magnet, like the one I used, it should be...
thingiverse
Customized version of http://www.thingiverse.com/thing:147452 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=147452
prusaprinters
Magnetic Sharpie mount with press fit magnets this print uses magnets that measure 12mm round by 2.8mm thick.https://www.etsy.com/listing/1288896022/3d-printed-sharpie-mountsholder-magnetic?ref=listings_manager_grid
thingiverse
Wanted a sharpie cap with a magnet cap to put one in my workroom and one on my fridge. Designed it then realized V1 was a touch..... phallic. So made V2 which I'm much happier with. Freecad files attached for both versions. Magnet size: 12mm x...
thingiverse
So I designed a sheath that securely holds the cap of a large chisel tip sharpie, then inserted a magnet. This design is specifically for a LARGE CHISEL TIP SHARPIE. It will not work with any other marker/sharpie design. You will need a 18mm (dia)...
thingiverse
Magnetic Sharpie holder. Quickly locate and grab sharpie without worrying about losing cap. Cap is held in place allowing easy replacement. gives you a clear visual of missing pens. ... You will need 1) M6 x 60mm flat head screw 1) M6 nut 3)...
prusaprinters
This clips to your cap in a second and allows you to grab and store your sharpie in half that time when you need it. There is a slight angle on the clip to keep the sharpie somewhat out of your line of sight and prevents it from interfering with...
myminifactory
A remix of Areeve20's "Sharpie Cap Screwdriver", Bulked out a bit, and added a slot where a small magnet can be mounted.I printed this remix with a Makerbot 2 so I redesigned some components to work more smoothly with this 3d printer in particular.
thingiverse
Print the cap, buy TWO D2H1 magnets, mount magnet, use as a screw driver/ sharpie cap. ( I bought mine here: http://www.kjmagnetics.com/proddetail.asp?prod=D2H1 ) More detailed instructions: Stick the magnets onto the flat base of a screw driver bit,...
prusaprinters
Print in vertical orientation, use supports for magnet slot.8mm x 3mm circular Neodymium magnets are easy to find online or at hardware stores.
thingiverse
Screw in a 16mm x 5mm Countersunk Magnet like these: https://aussiemagnets.com.au/product/-16-x-5mm-Pot-with-3.5mm-Countersunk-Hole-%28Rare-Earth%29.html
thingiverse
Magnetic Sharpie mount with press fit magnets this print uses magnets that measure 12mm round by 2.8mm thick. ... https://www.etsy.com/listing/1288896022/
thingiverse
Magnetic Sharpie mount with Sealed in magnets this print uses magnets that measure 12mm round by 2.8mm thick. dont forget to add in a pause print when slicing the file so that you can drop the magnets in the holes then continue printing to seal them...
prusaprinters
I started using a metallic sharpie to label vacuum sealed foods for the freezer but needed a way to store the marker top down instead of flat in a drawer.Sized to fit the cap of a metallic Sharpie snugly. Also, has spaces for 4 6x2.5mm magnets. ...I was...
thingiverse
Holder for Milwaukee Inkzall and Sharpie markers, with recess for 25mm rare earth magnet. ... Link for magnet: https://www.amazon.com/Neodymium-Magnets-Pull-Capacity-Each/dp/B07YSTJ4TR?ref_=ast_sto_dp&th=1
prusaprinters
The body of a fine tip Sharpie marker is tapered, so this is designed to either be dropped in place (if it's going to be kept in the appropriate orientation) or a gentle friction fit near the cap (if it needs to be mounted in another...
cults3d
Attach your Milwaukee Inkzall markers, sharpie markers, or highlighters to any magnetic surface! Pocket is designed for the use of seven 8x3mm magnets commonly found on Amazon.
thingiverse
Various Pen Holders which use16mm x5mm Magnets. The STAEDTLER one is a whiteboard Pen Holder and will also suit ARTLINE pens. ... KLOSE is a legendary CNC Machinist.
thingiverse
Magnetic wall mount Sharpie holder. Be sure to add a pause in the print to insert the magnets. Using PrusaSlicer, a 'fake' color change worked well @ 2.6mm. There are 7 magnets that are 10mm Dia x 2mm Thick. ... Fusion 360 file included as well.
thingiverse
... even the "mold draft" size difference along the length of the tube. The result is a snug fit when making models for actual Sharpie! More about this on my projects blog, here: https://theheadlesssourceman.wordpress.com/2018/05/09/sharpie-3d-model/
prusaprinters
https://www.etsy.com/listing/1288896022/3d-printed-sharpie-mountsholder-magnetic?ref=listings_manager_grid