shendrones mixuko 3d models
577 3d models found related to shendrones mixuko.thingiverse
Aeropod for Shendrones Mixuko, Full Tilt Boogie, or Flaco. ...Print in TPU.
thingiverse
Must be printed with a flexible filament (TPU/TPE/etc) This is a pod/cover for the Shendrones Mixuko x-frame. It replaces the top camera plates, and is designed to work with the HS1177 camera, setting it at a 45° angle. The bottom section is intended...
thingiverse
Designed a shroud to be used instead of the standoffs that are included, this shroud is 22mm high and have cutouts for the Naze32 rev6 FC. Added a new design for the NAze32 rev5 with the USB port out the back... Print Settings Printer Brand: ...
thingiverse
Shendrones Mixuko GoPro & Xiaomi YI - Race Mod (Beta1) 30°
thingiverse
Shendrones Mixuko RunCam HD 2 Race Mod (Beta1)
thingiverse
TPU pod for holding a Samsung Gear 360 cam on a Shendrones Mixuko or Full Tilt Boogie.
cults3d
Mixuko 5" Runcam Micro Swift Camera mount. Designed to be printed in PTU so there's flex and can be "pinched" between the side frames. This replaces the carbon camera mount that has always been a pain to keep from wiggling and to keep the camera...
thingiverse
Mixuko 5" Runcam Micro Swift Camera mount. Designed to be printed in PTU so there's flex and can be "pinched" between the side frames. This replaces the carbon camera mount that has always been a pain to keep from wiggling and to keep the camera...
thingiverse
This is my radical race pod for the Shen Drones Mixuko 5" frame. This pod is designed for a very short/tight 30x30 stack (FC and 4in1 esc) and a micro (19mm wide) camera with a 12mm dia lens (I'm using a swift micro v2). It has a place for a TBS...
cults3d
This is my radical race pod for the Shen Drones Mixuko 5" frame. This pod is designed for a very short/tight 30x30 stack (FC and 4in1 esc) and a micro (19mm wide) camera with a 12mm dia lens (I'm using a swift micro v2). It has a place for a TBS...
thingiverse
Here is my take on an easy to print simple camera mount for all 19mm cameras. Protection should be sufficient for most small cameras. Should be printed with a flexible filament such as TPU. ...Here I used a gyroid infill at 15% with a brim to keep...
thingiverse
ESC under-arm fairing similar to those originally seen on the ImpulseRC Helix frames. Has notches for wiring that can be cut out where needed. ...
thingiverse
This mount was designed to fit an HS1177 into an Shendrones Krieger Frame. ...It is also compatible with the Mixuko, where the cam is mounted into the frame and afterwards the assembly is secured to the Frame
thingiverse
Shendrones Full Tilt Boogie or Mixuko VTX Plate. Allows you to mount your VTX (or RC receiver) across the rear standoffs of the frame. Designed to work with the Zoompod GoPro Hero pod by Andy Shen as the SMA mount is in the top-rear of the pod. ...
thingiverse
Hello, remixed jpryor27 great Shendrones Pod. The pod got holes to ziptie antenna. ... V3 also got a bag for unify 5v v4 got a bag for unify and buzzer (reupload, first version didnt work with every cam)
thingiverse
GoPro Hero 3-4 pod for Shendrones Mixuko, Full Tilt Boogie, or Flaco.
thingiverse
Xiaomi Yi mount for Shendrones Mixuko remixed from "Xiaomi Yi - The Fpv Frame by Motorpixiegimbals" and "Mitsuko/Mixuko Session Mount by andyshen" Print Settings Printer Brand: RepRap Printer: P3Steel Rafts: No Supports: Yes Resolution: 0,1 Infill:...
thingiverse
Mount for using a Nerdcam on a Shendrones Mixuko or Full Tilt Boogie. ...Print in TPU, mount has to flex open to install Nerdcam.
thingiverse
This is a shroud and antenna mount for the Shendrones Mixuko. Weights in at 9grams at 100% infill. Print Settings Printer: Creator pro ...
thingiverse
Shendrones Mixuko 5 This is a remake modelled from a picture. So the measurements are not 100% accurate. The mid standoff is 25mm in height and the side plates are hold by a 36mm spacer. Motor mid points are symmetric on a circle of 196mm. ...YouTube...
thingiverse
Mount for Samsung Gear, works with Shendrones Mixuko, Full Tilt Boogie, or Flaco. ...Print in TPU, mount has to flex to insert camera.
thingiverse
A Session mount for Mixuko's and Mitsuko's by Shendrones. ...The mount slips over the top standoff and snaps into holes in the horns of the fpv camera mount.
thingiverse
MIXUKO is a 5 inch racing drone designed by shendrones (www.shendrones.com/mitsuko). This mount supports mobius (or runcam) and also allow mounting the receiver antenna in 45 deg vee (using zip-ties and shrinking tube). This thing was made with...
thingiverse
This is a WIP model I am testing for my Mixuko with a Runcam OWL Plus. The mounting holes are for M3 standoffs at 40mm OC. I will have final models in 20, 30 and 45 degrees. Comment if you want another angle. Eventually I will make an adjustable...
thingiverse
Customized version of http://www.thingiverse.com/thing:1567760 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1567760 Instructions Using the following options:...
thingiverse
A very light Whoop frame, about 4.5 grams in Taulman 645 and 3.6 in Nylonx. ...Glue the two parts together with Taulman Complete glue. More about it here: http://www.shendrones.com/babar
thingiverse
http://www.shendrones.com/hovercraft The main body is 160x200mm, print it in 2 pieces if necessary. Both one and two piece versions have a 'raft' option, a .6mm lip to help keep the print from curling. Cut it off after printing. ... The skirt also has...
thingiverse
... frame, use the unguarded top for 1s, guarded top for 2s. ...Both frames share the same bottom. Print in nylon, glue together with Taulman ComPlete. Pillars included in files for your convenience. Read more about it here: http://www.shendrones.com/babar