shure a400smxlr 3d models

Shure Microphone

Микрофоны Shure 5575LE

This is the Shure logo made into a 3d printable file.

Shure SCM audio mixerIt's a simple modell but wiht the right size

A closed-back, circumaural headphone from Shure, crafted with black hard plastic earcups, carbon fiber caps, aluminum alloy yokes, a protein leather headband, and memory foam earpads wrapped in Alcantara. Modeling done in Maya, textures done in...

Push button Micro Shure

SHURE SM58 DYNAMIC MICROPHONE

Shure needle headshell

Shure needle adapter

SHURE sm58 microphone with stand

my mic holder shure sm58, sm86 compatible.

Shure 55SH. ...The legendary „Elvis-Microphone“ see also: Microphone Shure (continuation)

Replacement part for Shure SHR-440 Headphones (broken hinge)

Drums Shure mic stand, for PG, PGA, PGD models

Drums Shure mic stand, for PG, PGA, PGD models

Shure sm7b all credits go to https://camerafoundry.com/products/sm7bs

Microphone wall holder for Shure SM58, wired Compatible with almost every wired microphone

I've added fastening for a shure sm57 (and similars) to the original model.

Clip to hook on back of T-shirt for Shure SE215 Wireless Earphones SE215SPE-B-BT1-EFS

Hotshoe Mount for Audio Mixer Shure FP33 or FP32A . ...Good suitable for fixing audio recorder or accessories .

The simple Pop filter for the Shure BETA87A microphone. ... Audio samples: https://bit.ly/2tf7R1j - clean https://bit.ly/2HXWKiA - with a pop filter

I designed this to replace the broken hinges on my Shure SRH440 headphones. It is a single part instead of two like the OEM hinge. ...

JMC 3D To demonstrate the difference between mic positions, I grabbed two Shure SM57s and set them up in different positions across the front of a 12″ speaker and putted in a simple XCLIP

After some time without use, my Shure SLX4 audio receiver's antenna cover plastic was very brittle and broke. ...I designed a replacement part using Fusion 360 (see design atteched).

Shure SRH840 поломалась дужка крепления одного из наушников. Спроектировал в КОМПАС-3Д. Можно еще доработать для более точного соответствия оригинальной детали, но уже в таком видео оно вполне работоспособно. ...

This is a replacement hinge for the Shure SRH 840 headset. After breaking a total of four hinges, i decided to make my own version, so i don't have to wait two months until they are replaced by the factory. It fits really snugly, to make sure that...

Because I'm a Scooter fan, I decided to model his so special microphone that he always holds in his hand in his clips and on stage. ... This microphone is the Shure 520 DX : http://equipboard.com/pros/scooter https://www.youtube.com/watch?v=F7cf2Eu4www

A tray that holds 6 Shure SM58 microphones so that they take up minimal space in the case drawer without flying around. It features a space for 19mm spike tape for labeling as well as slots to easily grab the mics.

This is a SHURE BLX4R Receiver wall bracket I designed for my church when we purchased our wireless mic. This bracket uses the mounting holes of the receiver and the included screws to mount the receiver to the bracket. ...It works great and, as you can...

Hello, Just, I make the fixation of the cable for put every where on the stand :) (just two only in the pack) this pack : https://www.gear4music.com/PA-DJ-and-Lighting/Shure-SM58-Dynamic-Vocal-Mic-with-Stand-and-Cable/C39 ;) Joss