sonicare charger 3d models

Wall holder for Philips Sonicare charger. ...Enjoy.

Wall holder for Philips Sonicare charger. ...Enjoy.

Dock and plug holder for Phillips Sonicare 4100 (shorturl.at/akmwZ)This works with the charger that comes with the product and allows you to tuck the cable within the print. ...&nbsp;<br><br>Supports required.</p>

I stumbled on this model: https://www.myminifactory.com/object/3d-print-sonicare-toothbrush-tooth-charging-base-153821 and showed it to my kid who just got a new sonicare toothbrush. She wanted me to print it, however when I printed it was too small...

My sister thought her toothbrush charger wasn't stable enough, so she asked me to print a base that would keep it from falling over when the toothbrush was charging. ... The charger should just fit right into the opening.

## What is this Staple-able Phillips Sonicare charger wall mount for plaster board wall. ## How to use * Install the mount with normal stapler and needle * Recommended to use stain-less steel stapler needle to avoid rusty stain from the wall ...

Sonicare Toothbrush charger shelf for 2 chargers

This is a Sonicare Dual Charger Stand. it holds 2 chargers, 2 brush handles and 2 brushes. the chargers snap into place and are held securely. it also has 8 feet on the bottom to allow air flow underneath the stand. The feet are a tight fit, so...

I recently installed a new bathroom cabinet and wanted to put my Sonicare toothbrush charger inside it. The charger holder that comes with the toothbrush didn't allow for easy access to both toothbrushes. Because of the narrow depth of the cabinet,...

It fits the charger for my Panasonic Sonicare toothbrush snugly enough that I can screw the holder to a shelf, then snap the charger into it, and it won't move. There's a gap in the back for the power cable. Once I do designs for the other two items,...

Sonicare HX6100 charger wall mount. This charger is used for lots on different sonicare model brushes. its a snug fit some very minor sanding or careful flexing may be needed to get it in. I used ABS which tends to shrink, PLA may make for a easier...

... same shelf. When done, this will fit the charger for my Panasonic Sonicare toothbrush charger snugly enough that I can screw the holder to a shelf, then snap the charger into it, and it won't move. ...There's a gap in the back for the power cable.

... the chargers in the dock some heating with a hairdryer could be of help. Print Settings Printer: ct Rafts: No Supports: Yes Resolution: 0,2 Infill: 10 Notes: While inserting the chargers in the dock some heating with a hairdryer could be of help.

Remix of [Sonicare HX6100 wall mount](https://www.thingiverse.com/thing:1118084) that can be used with 1 1/8" suction cups to mount to a mirror. ...

The cord of the charger is too short to let the charger sit on the plank below the outlet, and the low weight of the charger and toothbrush make it susceptible to falling off the plank above the outlet. So, to solve this, I created a holder for the...

The cord of the charger is too short to let the charger sit on the plank below the outlet, and the low weight of the charger and toothbrush make it susceptible to falling off the plank above the outlet. So, to solve this, I created a holder for the...

This is based upon the great design from https://www.thingiverse.com/thing:3708131 I removed the brush holders because each brush model has a different size and added additional toothbrush holders. ...Since I don't use the original toothbrushes, the...

Sonicare Toothbrush Stand + Charger Holds: -Most NEWER Sonicare Toothbrushes -Most NEWER Sonicare Charging Bases -2 Sonicare Toothbrush Heads Edit: -Removed the back legs to allow for optimal printing. -Widened toothbrush opening for easier placement...

Philips sonicare stand with place for charger. Fits well for Philips 2 Series HX6232. ... There is place for stock charger inside stand.

A holder for two Sonicare brush heads and a charging stand. My model is an EasyClean (Hx6511/34). It's designed to attach to the wall with two medium-sized Command strips. This is something of a prototype, it doesn't have to be as wide as it is,...

... ...Within a week of purchasing my fabulous Sonicare toothbrush I knocked the glass cup onto the floor, shattering it into pieces. This is a plastic replacement that will not break when dropped, but will also not hold water... ...so the choice is yours!

... This was made for Philips Sonicare chargers. I don't know if it works for other types of chargers. If they have the same dimensions, it will work. Sorry if the orientation of the STLs is not correct. ...This is how SolidWorks spat it out.

History: I buy toothbrush with charger with plastic non-stable socket for charging. So I design this thing. It also glow when toothbrush is charging. For glowing I use: *solenoid with 20 coils. I use enamel copper wire from secondary...

Philips Sonicare toothbrush holder with room for two toothbrushes and a charger in the middle. The charger slot is a friction fit and holds the charger snugly with no wiggle or movement. There is a slot at the back to allow the cord to run beneath...

Was looking for a wall plug for a new Phillips Sonicare and found one that might work, https://www.thingiverse.com/thing:3566319/files was close. I modified his wall plug holder for a US 110 V plug but the final assembly stuck out too much that the...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/gkS6Vl8u7ux

My dog destroyed the inductive charging cover for my plug-in charger for my Philips Sonicare toothbrush. I was able to get it to a height above the stand that seems to charge it properly. Surprisingly the toothbrush still works. ... ...

I saw the holder and liked the basic design, but I wasn't too fond of the idea of the charger cable just going up and out of the holder, so I decided to customize it for my own purposes by modifying it with a cord wrapping design. NOTE: As of my...