spool bed 3d models
159506 3d models found related to spool bed.
thingiverse
If you like my designs please consider buying me a coffee! DIY LCD Case https://www.thingiverse.com/thing:2523148 DIY YZ Base here: https://www.thingiverse.com/thing:2509242 DIY Z Axis here: https://www.thingiverse.com/thing:2489051 DIY Y Axis here:...
thingiverse
Printable filament spool to fit small beds such as Flashforge Finder's bed. ... It's compatible with Ecofila's refills.
thingiverse
Spool holder, remix of the TUSH. Designed to fit on to a 100mm bed. Uses 608 bearings the same as original. ... Includes holes through center of bearings for m3 or m3.5 bolts (not required as it holds itself together quite well) and a horizontal slot...
thingiverse
The original was too big for my little print bed. I also added a battlements ring where I removed every other top stone. Well... kinda. I screwed up the order and ended up with a couple together instead of every other one. Still, I kinda like the...
cults3d
... steppers that feed the filament through, causing it to slow or not feed at all. I found the replacement spool holder for the rear of the Fabriktor Mini 2 wasn't really that great, and all other spool holders were bigger than my print bed itself.
thingiverse
... steppers that feed the filament through, causing it to slow or not feed at all. I found the replacement spool holder for the rear of the Fabriktor Mini 2 wasn't really that great, and all other spool holders were bigger than my print bed itself.
thingiverse
This spool holder is designed for larger spools with up to 360mm diameter and splitted to be printed on smaller print beds. There are also three different types of guides available. ...Usage of the guides may reduce the available spool diameter.
thingiverse
This is a master spool compatible with the EconoFil™ filament spool refills by Filaments.ca™ specifically designed as multiple parts that can be printed on small print beds. The complete spool halves are assembled with screws to ensure strength. The...
thingiverse
This is a spool holder that should work with a dollar store broom from China. Not all brooms will work but I took a couple measurements and this should work with a lot of stuff. You may need a hack saw but it may also work without. I used a hack...
thingiverse
Actual Spool - Modeled off of a Hatchbox Spool. ... Find out how well your bed is leveled and if you have your bed centered. ... Nice way to tourture test your rig.
thingiverse
Customized version of http://www.thingiverse.com/thing:355889 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=355889 Instructions Using the following options: L = 80...
thingiverse
Shorter by 10mm, Requested Change to fit 220x220mm bed
thingiverse
I bought a cheap roll of filament that didn't come with a spool. The available designs all were too big to print on my Flashforge Creator Pro (which is not small, but also not large). So I designed this one. ... Since it is done in Openscad it...
thingiverse
2 spool adapter 523mm to 10mm that fit into printbed of kiwi sharebot . ... I used this spool adpter for my 750 g sharebot spool .
thingiverse
gfretz's spool rack was a bit too large for my printer, and it didn't work well when I tried to print by scaling it down, so I remixed it in Tinkercad by reducing the size. ...I also got 3/4" dowels so adjusted the holes for that.
thingiverse
I redesign a little bit because it was just to big for my smal building platform on my Easythreed Nano 3D printer. ...I will need a other spool holder for big spools, because the nano spool holder is only voor 350 gram spools from Easythreed.