spool rods 3d models

This is a smaller spool rod holder that I designed perfect fit for Inland filament for the Dremel 3D20 / Flashforge Dreamer This is compatible with https://www.thingiverse.com/thing:652415

OmniStand Extra Long Filament Spool Rods These filament spool rods allow the quick connect OmniStand and Non-Quick Connect OmniStand to hold slightly wider filament spools. These rods were originally part of the OmniStand set but were removed because...

Instructions I printed the spool rods vertically. I printed the rod holders lying on their front side with external support. Supports were relatively easy to remove using Simplify3D but I have always had trouble with FlashPrint and supports. I...

I cut the ends off oneaday's 88mm rod. ...Edit: 2016-11-24 oneaday have updated his rods!http://www.thingiverse.com/thing:1660600 Print Settings Printer: Original Prusa i3 MK2

This is a spool rod holder designed to be bolted onto a container.

Spool rod holder for a DIY drybox or anything that uses a 1" OD rod. ...Fastener holes are for #8-32 bolts Thanks for your consideration.

Spool rod holder for a DIY drybox or anything that uses a 1" OD rod. ... Fastener holes are for #8-32 bolts Thanks for your consideration.

Different design of the filament spool rod in order to reduce material usage and print time. Fits the base mentioned in the remix. ... Two different sizes are included in the Sketchup file.

This is a very basic print for a filament spool rod to fit this Thing http://www.thingiverse.com/thing:1743661 for the Tevo Black Widow. It's also a pretty good test for your printer as to having a level bed and your x and y axis working in sync.

Took the printer mounts apart to perform some upgrades when Le Wifey accidentally threw my original Anycubic Kossel spool rod away. This eventually turned into my first Fusion 360 "project"... Works with these top mount brackets: ...

spool rod holder i made for my folger prusa. Made out of white abs 1.75mm at .2mm height. it can hold 4 to 5 spools on the inside and some filiament that not on spools on the outside. any type of 8mm or smaller rod can be use. wood is the only thing...

This is a spool rod holder that plugs into the Ivar shelving unit by IKEA.

I was asked to upload a spool rod for the original size of the Rostock Max spool mount. So here it is. ... Instructions Per Request: Someone wanted the rod split in half

Needed a longer spool rod / pipe how ever you want to refer to it for a SainSmart roll. ... Fits on the standard spool holder, using the original spool nuts.

Support base with top to capture a rod for holding filament spools. ... I used 3/4" Oak dowel for the spool holder rod and small countersunk wood screws. ...

I added an enclosure to my FT5 and the original spool rod holder was not tall enough and the spool would hit the new top piece. This is a slightly taller holder with a smaller profile. While this was intended to be used on my FT5/6 it can be used...

Diameter 7.7 mm Length: 120 mm I made these so i could use the Prusa Printer Enclosure V2 (MMU2 compatible) but I didn't have the MMU or MMU2 so I didn't have the metal spool rods that I could re-use but I did want to use the 5 spool holder design...

Filament spool rod hanger (remix from Robinder's spool rod hanger https://www.thingiverse.com/thing:3676334)The hanger is designed for OD=43mm pvc tube to be used with button head screws.Hardware required:m4 x12mm button head screws x6m4 nuts...

This is an add-on for: Lid Spacer with Spool Holder for Flashforge Inventor 3D Printer (Remix) https://www.thingiverse.com/thing:3574777 Instead of using wooden dowels for the spool holder, I made a 3d printable spool rod, and then an insert that...

... each side. Instructions Print two out (one for each side) Cut a 1 3/16" diameter rod to length. Slide the spools on and then the ends. I printed on M3D with Medium quality and Low fill. ... I included the .123dx file if you want to change it.

Summary One side of a spool holder for M3D filament spools or ones that are 4 1/2" in diameter. This utilizes standard closet rod for the going between each side. Instructions Print two out (one for each side) Cut a 1 3/16" diameter rod to length. I...

As Puddlefist stated, the 150mm threaded rod that comes with the Anet A8 spool holder is not quite long enough. A longer non-threaded rod is probably best, but this will use what you already have and the rod cannot slip out with normal use. ... ...

I created these to hold the rod that supported the spools in a plastic box I keep my filament in above the printer. Simple design but does the job, you will also need 4 M3 nuts and bolts to hold it in place. ... If you are interested in the spool...

To be used in conjunction with: https://www.thingiverse.com/thing:3174858 (Mirror it for dual spool mounting!) Slightly longer than the stock rod so it's easier to take off and put on the holder. ... Use 30.15mm cap for a snap fit, 30.25mm for a...

for multiple spools. ...in my 3DRAG with this support now i have 4 spools

Made for filament spools so that they can sit on a rack

http://www.thingiverse.com/apps/customizer/run?thing_id=1108314 Instructions Using the following options: hanger_height = 35 inner_tab_height = 15 hanger_width = 47 rod_length = 85 rod_pitch_angle = 1.0 stopper_margin = 6 hanger_wall = 6 rod_height =...

http://www.thingiverse.com/apps/customizer/run?thing_id=1108314 Instructions Using the following options: slot_thickness = 8 rod_pitch_angle = 1.0 inner_tab_height = 15 rod_diameter = 37 hanger_width = 47 hanger_wall = 6 stopper_thickness = 4...

... of an end fitting for an 8mm nut. ... It is sized to fit inside the nut of the spool hub http://www.thingiverse.com/thing:1241566 so everything works as a unit. ...How I Designed This I imported the original file into SketchUp and re-sized it to 95%.

I built an enclosure from some Ikea cabinets and wanted to mount the spool below the build chamber with the power supply. This low profile mount uses the stock plastic nut that came with my printer (Monoprice Maker Select, possibly other i3 clones...